Q5. The Figures below shows a simple bolted single lap joint plate and a simple bolted double lap joint plates under a load of P (N). Each bolt lap joint uses the same bolt with a diameter of d (mm). Which option correctly shows the shear stress (T) equations for the bolt in the single and double lap joint plates? P/2 P/2 d d. Simple Bolted Single Lap Joint Simple Bolted Double Lap Joint O a. Pd Tsingle Pd and tdouble = 2n2 %3D 4n2 Ob. 4P and tdouble = 2P Tsingle %3D па? па? С. Tsingle and Tdouble = Pd² %3D Pd d. P and Tdouble = 4nd? P Tsingle = 2nd?

Q5. The Figures below shows a simple bolted single lap joint plate and a simple bolted double lap joint plates under a load of P (N). Each bolt lap joint uses the same bolt with a diameter of d (mm). Which option correctly shows the shear stress (T) equations for the bolt in the single and double lap joint plates? P/2 P/2 d d. Simple Bolted Single Lap Joint Simple Bolted Double Lap Joint O a. Pd Tsingle Pd and tdouble = 2n2 %3D 4n2 Ob. 4P and tdouble = 2P Tsingle %3D па? па? С. Tsingle and Tdouble = Pd² %3D Pd d. P and Tdouble = 4nd? P Tsingle = 2nd?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mechanical design
For the frame shown in Fig. 6-24a, draw the free-body diagrams of (a) the entire frame including the pulleys and cords, (b) the frame without the pulleys and cords, and (c) each of the pulleys. 3E Fx=0 +9 E fy=o 1. FIMD RXAS AT A$D Fing FoRLE componeAB 2. Ge Pits oF POLLEYS EM=0 Cx C By E Ay T. Ay AauLE OF RESOUTAT AT B, C &A 75 lb SKETCH RESULTALT (a) Fueo Manat AT BASE ア(y 7516 OF CULUneCE radius of the pulley at B linch Yadius of the Pulley at c a7s inch 75 lbs 7516 () Distance BE 7inch Distance EA 4.5 inch Distance AV : 3.sinch Ay 6) 7516 マへ

Bolts distributed about a bolt circle are often called upon to resist an external bending moment as shown in the figure. The external moment is 19 kip-in and the bolt circle has a diameter of 15 in. The neutral axis for bending is a diameter of the bolt circle. What needs to be determined is the most severe external load seen by a bolt in the assembly. M Neutral axis R NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. View the effect of the bolts as placing a line load around the bolt circle whose intensity FÅ, in pounds per inch, varies linearly with the distance from the neutral axis according to the relation Fb Fb,max R sin 8. The load on any particular bolt can be viewed as the effect of the line load over the arc associated with the bolt. For example, there are 12 bolts shown in the figure. Thus, each bolt load is assumed to be distributed on a 30° arc of the bolt circle. Under these conditions, what is the largest bolt…
The bracket shown in the figure is bolted a ceiling beam to support a fluctuating vertical load imposed on it. The bolts are -in coarse-thread SAE grade 8, tightened to recommended preload for nonpermanent assembly. The stiffnesses have already been computed and are kp=4 Mlb/in and km = 16 Mlb/in. Laad line F. Steady stress (a) Assuming that the bolts, rather than the welds, govern the strength of this design, determine the safe repeated load that can be imposed on this assembly using the Goodman criterion with the load line in the Figure and a fatigue design factor of 2. (b) Compute the static load factors based on the load found in part (a). (ie. Yielding factor of safety, Load factor of safety and factor against joint separation)
A 30-mm thick AISI 1020 steel plate is sandwiched between two 10-mm thick 2024-T3 aluminum plates and compressed with a bolt and nut with no washers. The bolt is M10 x 1.5. property class 5.8. (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members.
I keep getting this one wrong. For T1, I did 370/cos(30) = 427.24 lb tension , and -427.24 x cos(30)= -370. I also tried T1=820, and T2=-710.14, which was not correct as well. Thank you for your help on these two parts
The carrier plate material St52 (S355) given in the figure below is welded to the body. combined. F1 = 4 kN and F2 = 40 kN static forces act on the plate. Source I. Quality (v2 = 1), no impact (v3 = 1), weld thickness a = 5 mm, safety coefficient s = 2 and weld seam coefficient v1 = 0.8 will be taken. Find out whether a = 5 mm weld seam thickness is sufficient or not, according to the data in the figure and above.
How we draw the freebody Diagram for B ( and how we relove it with angle 60 dgree ) ???
A bolted lap joint using ISO 5.8 bolts and members made from cold-drawn SAE 1040 steel is shown in the figure. Assume the bolt threads do not extend into the joint. Find the tensile shear load F that can be applied to this connection to provide a minimum factor of safety of 2.5 for the following failure modes: shear of bolts, bearing on bolts, bearing on members, and tension of members. 40 ↑ 70 40 ↑ 80 M20 × 2.5 20 20
The figure shows a section of a large coupling. Each bolt in this joint is subjected to cyclic load fluctuating between 0 and 13 kN. The members are made from steel. The members have equal thicknesses and total length of members is L=37 mm. Each bolt is initially tightened carefully to 78% of proof load. The bolt is to be Metric grade 5.8 M12x1.75 (coarse-pitch series). The threads has been manufactured by rolling and reliability for bolts is 95%. Calculate the stiffness of the bolt (in kN/mm). Yanıt:
The eye screw, shown in the figure below is subjected to a force of 35 kN. The material of the screw is steel with ??=355 ???. The safety factor is 1,5. Calculate the minimum diameter of the thread.
Tassimo mikanikium