01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wallthickness of 0.25 in, is fastened to a solid aluminum rod (2) that has a2 in. diameter and a solid aluminum rod (3) that has a 1.375 in.diameter (E -30,000 ksi, E-10,000 ksil. The bar is loaded as shownin figure below, Determine:(1) the displacement of point D with respect to the fixed support at A.(2) the maximum normal stress in the entire axial assembly.(3) the normal strain in the steel tube (1).34 kips18 kips25 kips18 kips34 kips60 in.40 in.30 in.

Solution: Force acting at A can be found by, FA-34+18-25=0FA=-41kips Free body diagram of each…

01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in, is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter (E-30,000 ksi, E-10,000 ksil. The bar is loaded as shown in figure bolow, Determine: (1) the displacement of point D with respeet to the fixed support at A. (2) the maximum normal stross in the entire axial assombly. (3) the normal strain in the steel tube (1). 34 kips I8 kips 25 kips 34 kips 18 Kips 60 in. 40 in. 30 in.

01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in, is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter (E-30,000 ksi, E-10,000 ksil. The bar is loaded as shown in figure bolow, Determine: (1) the displacement of point D with respeet to the fixed support at A. (2) the maximum normal stross in the entire axial assombly. (3) the normal strain in the steel tube (1). 34 kips I8 kips 25 kips 34 kips 18 Kips 60 in. 40 in. 30 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a cross-sectional area of 40x40 mm and a wall thickness of 4 mm, is subjected to an axial tensile load of "6" KN from both ends. remains. (E1045 = 207 GPa, Yield 1045 = 414 MPa) Calculate %3D %3D the final length of the rod under this tensile load in "mm".
0:07I | ZVAO K/s a 15all KOREK A locs.google.com 11 Q2: The extension spring shown in the figure has full-twisted loop ends. The material is AISI 1040Q&T 400FO wire. The spring has 82 coils and is close- wound with a preload of 18 Ibf. (a) Find the closed length of the spring.(b) Find the torsional stress in the spring corresponding to the preload.(c) Estimate the spring rate.(d) What load would cause permanent deformation?(e) What is the spring deflection corresponding to the load found ?in part d 0.162 in 1 in L-in R -in R. Option 1 O
MACHINE DESIGN1
suppose the free length is 65 mm. Find the stress at solidity in units of MPa Circle final answer
Mechanical design
S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B and D pins (B single cut D double cut), the thickness t of the BD bar. (Safety Cat.(S)=2, T = 250 Nmm2 o -350 N/mm2) 40.a mm 300 mm a=9.6 TAKE 60.a mm 50 mm D Yatağı 100 mm t mm F=100 kN
= The L 37 in. long structural member shown below is fabricated with a solid copper core and a stainless steel cover that are bonded together to form a composite shaft. The copper core has diameter Dc = 1.4 in The stainless steel cover has inner diameter (Din)s = 1.4 in. and outer diameter (Dout) ss ss = с = 1.65 in. A torque of T = 104 ft lb is applied at its free end, which is shared between both the copper and stainless steel. Determine the angle of twist of the composite shaft and the maximum shear stresses in the copper core and the stainless steel cover. = -.39 (Tmax) ss = 869.295 (Tmax) c = = 1834.97 L Stainless steel Copper core ? × 0% psi × 0% psi ? × 0%
Please try to solve in 30 minute
For the joint shown in the figure, if F = 28 kN and dn = 12.8 mm, calculate: 7.5 mm F F 12 mm 12 mm 7.5 mm - de - F 18 mm - F 18 mm 125 mm 1. The largest bearing stress in MPa between the pins and the members; a. 146.23 MPa b. 182.29 MPa c. 174.56 MPa d. 199.37 MPa 2. The average shear stress in MPa in the pin and; a. 108.80 MPa b. 116.14 MPa c. 136.23 MPa d. 98.01 MPa 3. The largest average normal stress in MPa in the members. a. 181.23 MPa b. 175.76 MPa c. 191.26 MPa d. 150.32 MPa
La Figure: Compression spring The squared type of compression spring has total 8 coils shown in the figure. The spring is made of music wire with wire diameter and mean diameter of 0.30 inch and 3.0 inch respectively. Initially the free length of the compression spring was proposed as 3.75 inch. Is this safe to compress the spring to the solid length (L.) considering the factor of safety 1.5? If it is safe why it is safe? Show your calculation. If this is not safe, propose the maximum free length of this spring.
Solve it pls.
A bracket shown in Fig.(2) is fastened to the wall by four bolts equispaced on a (10 cm) diameter bolt circle. The bracket is subjected to a fluctuating force (0-50 N) . Find the forces acting on each bolt and then choose a suitable bolt size and a preload that will give minimum safety factor (1.5) for any mode of failure.