A bolted joint consists of 40-mm thick AISI 1020 steel plate sandwiched between two 12-mmthick aluminum plates and compressed with a bolt and nut with no washers. The bolt is M14x 2,property class 5.8.(a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm.(b) Determine the bolt stiffness.(c) Determine the stiffness of the members.(d) Determine the joint stiffness constant

GivenAISI 1020 plate thickness ts=40mmthickness of aluminium plate ta=12mmBolt MI4×2, property class…

A bolted joint consists of 40-mm thick AISI 1020 steel pl thick aluminum plates and compressed with a bolt and nu property class 5.8. (a) Determine a suitable length for the bolt, rounded up to (b) Determine the bolt stiffness. (c) Determine the stiffness of the members. (d) Determine the joint stiffness constant

A bolted joint consists of 40-mm thick AISI 1020 steel pl thick aluminum plates and compressed with a bolt and nu property class 5.8. (a) Determine a suitable length for the bolt, rounded up to (b) Determine the bolt stiffness. (c) Determine the stiffness of the members. (d) Determine the joint stiffness constant

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Determine Method of Joints. A 000 TH 30° 3m the force in all members using B 30° C 3m 2.7 KN 30 E 3m…

Q: A steel cantilever beam is made of two T-shaped structures welded to each other as shown in the…

A: given; q=2MN/mσ=150MPalength (L)=L1+L2 =1+.5 =1.5m

Q: A 30-mm thick AISI 1020 steel plate is sandwiched between two 20-mm thick 2024-T3 aluminum plates…

A: Bolt is an Joining member which are used to join no of plates. Bolt are must be designed carefully…

Q: Problem 3.1: Determine the design strength of a 1 mm length of a 6.35 mm fillet weld formed by the…

A: Given Data:Find:Determine the design strength in all the cases.

Q: 1.37 Link BC is 6 mm thick, has a width w = 25 mm, and is made of steel with a 480-MPa ultimate…

Q: A tie bar has to carry a load of 100kN. What must be the width of the bar, which is 12,7mm thick if…

Q: A cylindrical pressure vessel, mean radius 15 in, is filled with a gas of molecular weight causing…

Q: The weldment shown in Figure 2 is subjected to an alternating force F. The hot-rolled steel bar is…

Q: 4) A 15ft W12x40 steel column is supported by a steel base plate, concrete pedestal and concrete…

A: Given: length of the steel column=15ft=180in cross sectional area of the columnA=11.7 in2 axial…

Q: 9-29 The permissible shear stress for the weldment illustrated is 140 MPa. Estimate the load, F,…

A: Given Dataτs=140Mpad=75mms=6mm

Q: Determine the safe tensile load for fine series bolts of (a) M 24and (b) M 38. Assume that the bolts…

Q: What is the minimum cross-sectional area required of a vertical steel cable from which is suspended…

Q: Parvinbhai bhaliya

A: The objective of the question is to design a suitable column given the load, material, and boundary…

Q: The effective handle length of a wrench is 30 cm. The bolt is made of grade 5 steel. What is the…

A: Write the given data. l=30 cm5th grade steelF=50 NN=6 It is required to determine the minimum…

Q: Design a knuckle joint subjected to axial tensile force of 50 kN. Determine the dimensions and…

Q: 24 kips D C00 All Members: A = 4.0 in E = 29,000 ksi 12 ft 9 ft 9 ft 12 kips 1. Determine the…

Q: Parvinbhai

A: The objective of the question is to design a suitable column given the load, material, and boundary…

Question

A bolted joint consists of 40-mm thick AISI 1020 steel plate sandwiched between two 12-mm
thick aluminum plates and compressed with a bolt and nut with no washers. The bolt is M14x 2,
property class 5.8.
(a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm.
(b) Determine the bolt stiffness.
(c) Determine the stiffness of the members.
(d) Determine the joint stiffness constant

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 20mm thick plate Fy = 250 Mpa, Fu = 415 Mpa, has 20mm nominal bolt holes. Using ASD and LRFD (NSCP 2015), the following apply. For tensile yiielding on gross section : Pn = Fy Ag, reduction factor = 0.90 (LRFD), factor of safety = 1.67 (ASD). For tensile rupture of safety = 2.00 (ASD). Determine the tension iin yielding capacity and tension rupture capacity of the connection. net area section : Pn = Fu Ae , reduction factor = 0.75 (LRFD) , factor 50 37.5 375 75 50 50 50 50 37.5 375 375 37.5 37.5 37.5
An overlapped fillet welded lap joint is subjected to cyclical stresses with a nominal stress range of 100 MPa. The maximum plate thickness for the adjoining members is 20 mm. The detail category is identified as 63. A capacity factor 0.90 can be assumed. What is the expected life in terms of number of cycles acccording to AS4100? Pick the closest answer. (a) 4.81x105 (b) 1.96×105 (c) 6.35×105 (d) 3.65×105 (e) 7.69x105
Assuming a welded rail line, 1km long, that is unconstrained except at the ends. The rail has a cross sectional profile as given. If the rail was installed at a temperature of 20°C, at what temperature would the rail buckle? How much pre-stress would need to be applied to the rail in order to prevent buckling up to a maximum operating temperature of 40°C? Rail profile 46E1 Equivalent profile name SBBI Section weight kg/m 46.17 Rail height mm (H) 145.00 X Y Y Head width mm (C) 65.00 A H Web thickness mm (A) 14.00 Foot width mm (P) 125.00 Moment of inertia, Ixx cm* 1641.10 Moment of inertia, lyy cm* 298.20
P
A 12” X 16”simply supported pine wood beam is being considered to carry a uniform load distribution across a span of 12’ as shown. In addition to the uniform load, the beam is also subjected to a tensile load of 20 kips. If the ultimate tensile stress in pine wood is 4500 psi, determine whether the beam is considered safe according to the Allowable Stress Method, using a Factor of Safety 2.5. Hint: you can calculate the maximum tensile stress in the cross-section without having to use Mohr’s circle
A 30-mm thick AISI 1020 steel plate is sandwiched between two 10-mm thick 2024-T3 aluminum plates and compressed with a bolt and nut with no washers. The bolt is M10 x 1.5. property class 5.8. (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members.
i just want to know how it is answer pls provide a thorough explanation
Quo 2.11. Design the longitudinal and circumferential joint for a boiler whose diameteris 2.4 meter and is subjected to a pressure of 1 N/mm?. The longitudiral joint is a triple riveted butt joint with an efficiency of about 85% and the circumferentialjoint is a double riveted lap joint with an efficiency of nbout 70 %. The pitch in the outer rows of the rivets is to be double than in the inner rows and the width of the cover plate is unequal. The allowable stresses are: 0,=7 MPa, r = 56 MPa and o̟ = 120 MPa. Asgume that the resistance of rivets in double shear is 1.875 times that of single shear. Draw the complete joint.
Pravinbhai
Can someone slove the fx and fy equations in the below questions solution in steps to how we got f1 and f2 values. Thanks.
Te - Effective throat thickness well in mm = 6 sin45° Consider the following drawing in which plate 1 is welded onto plate 2 as shown for tensile and shear loading. The plates are fillet welded with a weld thickness of 6 mm as shown for a length of 150 mm. The plates have an ultimate strength of 275 MPa and the welding was done with F70 welding electrodes, which possesses an ultimate strength of 483 MPa. Consider a partial factor of safety of 1.7 for the welded joint and determine the design strength of the weld joint, both in tension (Tdw) and in shear (Vdw) due to the forces acting on it. a) Determine the design strength of the following weld in tension ( ) due to vertical forces. b) Determine the design strength of the weld in shear ( ) due to horizontal forces. Attached pic is shear equation for calculation Tension equation for calculation is: Tdw = FyLwte /Ymw
Problem 2 Assume that Member AB may be considered as long and slender and consider only Euler buckling. What is the critical Euler buckling load and will Member AB buckle? What is the factor of safety of the compressive load with respect to the critical buckling load? Assume buckling only occurs in the plane of the paper. Note: E-30e6psi, I-6.36e-3 in', A-2.83 in², LAB-41.6 in, FAB-540 lb (compression). Also Member OB is 36 inches (3 ft) long. F=270 lbf 3 ft 3 60 A = 45270 LB, n = 83.8, buckles 48400 LB, n = A. Per B. Per C. Per = 1088 LB, n 897, does not buckle 2.02, does not buckle D. Per = 544 LB, n = 0.993, buckles E. None of These