An overlapped fillet welded lap joint is subjected to cyclical stresses with a nominal stress range of 100 MPa. The maximum plate thickness for the adjoining members is 20 mm. The detail category is identified as 63. A capacity factor 0.90 can be assumed. What is the expected life in terms of number of cycles acccording to AS4100? Pick the closest answer. (a) 4.81×105 (b) 1.96×105 (c) 6.35×105 (d) 3.65×105 (e) 7.69×105

An overlapped fillet welded lap joint is subjected to cyclical stresses with a nominal stress range of 100 MPa. The maximum plate thickness for the adjoining members is 20 mm. The detail category is identified as 63. A capacity factor 0.90 can be assumed. What is the expected life in terms of number of cycles acccording to AS4100? Pick the closest answer. (a) 4.81×105 (b) 1.96×105 (c) 6.35×105 (d) 3.65×105 (e) 7.69×105

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A static load of 30 kN is applied at the cantilevered beam as shown in the Figure 3.1 The cantilever…

Q: As an engineer you are asked to evaluate the feasibility of a device which operates in a temperature…

A: The initial temperature of aluminium is Ti=120°C. The tensile strength of aluminium is σt=-100 MPa…

Q: What is the largest force that can be applied to the part? The largest force that can be applied is…

Q: Assume you have a 30 mm in diameter AISI 1040 steel shaft welded on a rigid surface. Forces applied…

A: Given that, AISI 1040 steelDiameter of shaft, D=30 mm,Torque applied on shaft, T=40 N.mBending load…

Q: The shaft in (Figure 1) is used to transmit 32 hp while turning at 600 rpm. Figure 2 in. 2.5 in. 1…

Q: Two 1/4 in × 8 in A36 steel plates are joined with a lap joint using 3/4 in A325-N bolts. If a…

A: Steel plates of size 14 in × 8 in of A 36 steel Ultimate tensile strength of A 36 steel is…

Q: An M 14 x 2 hex-head bolt with a nut and a 14R washer under each of bolt head and the nut is used to…

A: Step-3: kb=(153.9×7)+(115×26)153.9×115×207=653.48mMN…

Q: Select the preferred diameter for an ASTM A227 cold-drawn wire that will have an ultimate tensile…

A: Given: A227 cold-drawn wire Ultimate tensile strength - 176 kpsi To find: Preferred diameter

Q: The central plates a in Fig.12 of the text are 9/16 in. thick and 9 in. wide. The diameter of the…

Q: For a bolted assembly with four bolts, the stiffness of each bolt is kb = 3.0 MN/mm and the…

Q: Two steels are being considered for manufacture of as-forged connecting rods. One is AISI 4340…

A: We need to find out the advantages of using these two materials.4340 Steel.Uncorrected endurance…

Q: repeat problem 8-19 with the bottom aluminum plate replaced by one that is 20 mm thick.

A: The total grip length is the sum of the thicknesses of the plates being clamped together. In this…

Q: A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height|…

A: Give:- At=84.3 mm2 F=12 kN To find:- g) Stress in bolt

Q: Answers provided as well.

A: Step 1: Step 2: Step 3: Step 4:

Q: A bolted joint consists of 40-mm thick AISI 1020 steel pl thick aluminum plates and compressed with…

A: GivenAISI 1020 plate thickness ts=40mmthickness of aluminium plate ta=12mmBolt MI4×2, property class…

Question

An overlapped fillet welded lap joint is subjected to
cyclical stresses with a nominal stress range of 100
MPa. The maximum plate thickness for the adjoining
members is 20 mm. The detail category is identified
as 63. A capacity factor 0.90 can be assumed. What is
the expected life in terms of number of cycles
acccording to AS4100? Pick the closest answer.
(a) 4.81x105 (b) 1.96×105 (c) 6.35×105 (d) 3.65×105 (e)
7.69x105

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A factor of safety of 2.5 is used for the bolts in the assembly below. The ultimate shear stress of the magnesium alloy bolts is 20.0ksi. What should be the diameter of the bolts? 10 kip 5 kip 5 kip Diameter = in
i need the answer quickly
A 30-mm thick AISI 1020 steel plate is sandwiched between two 10-mm thick 2024-T3 aluminum plates and compressed with a bolt and nut with no washers. The bolt is M10 x 1.5. property class 5.8. (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members.
Pc=nxdxtxo =2x25x20x150 150000 N The strength of the riveted joint= Least of P, Ps , Pc =150 000 N %3D The lap join the edges of There are th %3D 000 050= 02I X 0Z X 001 ='91d=d 0000$ =D0.625 or 62.5 % %3D 0000 a-single tr Homework: 1-A single riveted lap joint is made in 1.5 cm thick plates with 2 cm diameter rivets Determine the strength of the joint, if the pitch of rivets is 6 cm? Take 6,=1200 kg/cm ; o,= 900 kg/cm² ; 6=1600 kg/cm 2-Two plates 16-mm thick are joined by á double riveted lap joint. The pitch of each row of rivets is 9 cm. The rivets are 2.5 cm in diameter. The permissible stresses are as aqnop -4 c-paraller [ans:2827kg] 2. G,=1400 kg/cm ; 6,=1100 kg/cm² ; 6.= 2400 kg/cm 2. Find the efficiency of the joint . 3-A double riveted double cover butt joint is made in 1.2 cm thich plates with 18 mm diameter rivets.find the efficiency of the joint for a pitch of 8 cm. 2. 2. ст Take :6,=1150 kg/cm ; 6, = 800 kg/cm² ; oc=1600 kg/cm 10 mm thick, the allowable stresses are : 6, =…
Te - Effective throat thickness well in mm = 6 sin45° Consider the following drawing in which plate 1 is welded onto plate 2 as shown for tensile and shear loading. The plates are fillet welded with a weld thickness of 6 mm as shown for a length of 150 mm. The plates have an ultimate strength of 275 MPa and the welding was done with F70 welding electrodes, which possesses an ultimate strength of 483 MPa. Consider a partial factor of safety of 1.7 for the welded joint and determine the design strength of the weld joint, both in tension (Tdw) and in shear (Vdw) due to the forces acting on it. a) Determine the design strength of the following weld in tension ( ) due to vertical forces. b) Determine the design strength of the weld in shear ( ) due to horizontal forces. Attached pic is shear equation for calculation Tension equation for calculation is: Tdw = FyLwte /Ymw
"Using a 1-kg load at a specified joint, your experiment displayed that the bottom chord experienced a tensile force FBC of 2.1 N. If your computations showed that FBC is equal to 2.2 N (tensile), what is the percentage error?"