A part is loaded with a combination of bending, axial, and torsion such that the following stresses are created at a particular location: Bending - Completely reversed, with a maximum stress of 60 MPa Axial - Constant stress of 20 MPa Torsion Repeated load, varying from 0 MPa to 50 MPa Assume the varying stresses are in phase with each other. The part contains a notch such that Kibending = 1.4, Kaxial = 1.1, and Ktorsion = 2.0. The material properties are S,= 300 MPa and S, = 400 MPa. The completely adjusted endurance limit is found to be Se= 200 MPa. Find the factor of safety for fatigue based on infinite life. If the life is not infinite, estimate the number of cycles. Be sure to check for yielding.

A part is loaded with a combination of bending, axial, and torsion such that the following stresses are created at a particular location: Bending - Completely reversed, with a maximum stress of 60 MPa Axial - Constant stress of 20 MPa Torsion Repeated load, varying from 0 MPa to 50 MPa Assume the varying stresses are in phase with each other. The part contains a notch such that Kibending = 1.4, Kaxial = 1.1, and Ktorsion = 2.0. The material properties are S,= 300 MPa and S, = 400 MPa. The completely adjusted endurance limit is found to be Se= 200 MPa. Find the factor of safety for fatigue based on infinite life. If the life is not infinite, estimate the number of cycles. Be sure to check for yielding.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 2: Use an eigenvalue approach to solve for the principal stresses and directions for the state of stress shown below. Show the principal stresses on a properly oriented element of material. 20 mPa
Derive the following equation for computing shear stress in a solid bar along an oblique plane with angle B with respect to the vertical plane. The bar is subjected to centric axial loading. sin 0 cos 0 T = Ao
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
The supporting wheel on a scaffold is held in place on the leg using a 4-mm-diameter pin as shown. (Figure 1) Figure 1 of 1 > Part A If the wheel is subjected to a normal force of P = 3.3 kN, determine the average shear stress developed in the pin. Neglect friction between the inner scaffold puller leg and the tube used on the wheel. Express your answer to three significant figures and include the appropriate units. Tavg= Submit Provide Feedback Value A Request Answer C Units ? Next >
Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 10 mm and an allowable normal stress of 70 MPa. Pipe (2) has an outside diameter of 44 mm, a wall thickness of 8 mm, and an allowable normal stress of 170 MPa. Assume x1 = 2.9 m, x2 = 1.9 m, and y1 = 4.3 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B (1) (2) Answer: Pmax i kN
The cantilevered rectangular bar is subjected to the force of 5 kip. Suppose that L = 17 in. (Figure 1) Figure 1.5 in. A 1.5 in. 1 in. 1 in. B L 1 of 1 > 1.5 in. 1.5 in.j T 3 in. H 3 in. 5 kip Part A Determine the principal stresses at point A Express your answers in kilopounds per square inch to three significant figures. Enter your answers separated by a comma. 01,02 = Submit Provide Feedback ΓΙ ΑΣΦ | | Request Answer vec 5 ? Review ksi Next >
4) The C-clamp shown below has rectangular cross-section A-A that is 33 mm tall by 12 mm wide and the material is class 50 gray cast iron. Determine maximum tensile stress and factor of safety for clamping force F = 3.2 kN. Ignore stress concentration factors. See Section 4.9 in Norton for help with curved beams. MPa N O MAX |F F 60 mm 40 mm 12 mm 33 mm 33 mm Section A-A A
The bar is made from steel and has an allowable stress of allow = 19.7 ksi (Figure 1) Figure P 1.875 in. 0.75 in. -0.125 in. 1.25 in. r 0.25 in. 1 of 1 Part A Determine the maximum axial force P that can be applied to the bar. Express your answer to three significant figures and include the appropriate units. P = Submit μA Value Request Answer < Return to Assignment Units Provide Feedback ?
Example: Convert the change in length data in Table 3-2 to engineering stress and strain and plot a stress-strain curve Homework- help Table 3-2 The results of a tensile test of a 0.505 in. diameter aluminum alloy test bar, initial length (1o) = 2 in. Calculated LTO Load (Ib) Change in Length (in.) Stress (psi) Strain (in./in.) 0.000 1000 0.001 0.0005 4,993 14,978 24,963 34,948 37,445 39,442 39,941 39,691 37,944 3000 0.003 0.0015 5000 0.005 0.0025 7000 0.007 0.0035 7500 0.030 0.0150 7900 0.080 0.0400 8000 (maximum load) 0.120 0.0600 7950 0.160 0.0800 7600 (fracture) 0.205 0.1025
A cylindrical bar shown in the figure below has axial loads applied as illustrated. Calculate the normal stress in each segment, refer on the set section cuts. 13A 1.6 1.8 in 2 9000 lb 1.7A 12 in? 1.6 in 4000 lb 2000 Tb 7000 Ib (2 Match each item to a choice: Stress in AB Stress in BC Stress in CD Choices: # 2780 psi # 2550 psi # 3330 psi # 4210 psi # 3880 psi # 4380 psi
a) Refer to the figure below. Even though the cyclic loading accidentally caused the stresses to exceed the levels at point A slightly (as marked by the red arrow), the machine part may not break instantly according to the Modified Goodman fatigue failure criterion. True or False - Yield (Langer) line Gerber line - Load line, slope r = S„ISm Modified Goodman line S. I JA ASME-elliptic line Soderberg line ! Sm S, Midrange stress om b) good fatigue design should keep the fatigue design factor of safety at a minimum value of (_ Alternating stress o
Assemble a pair of parts A and B with serrated teeth as shown in the figure on the right.A compressive load of 24 kN is acting on the combined structure.The compressive load is transmitted by the three meshing teethTo. Shear stress and compressive stress (contact) generated in the tooth at this timeFind each tactile stress.