Q5 Design Straight bevel gear mesh for shaft centerlines that intersect perpendicularly with the following data Priori design Function Load (kW) 11 Speed (rpm) 924 Temperature (0C) 270 Pinion Life, NL (Cycles) 19232 Reliability 98.5 % Overload factor Uniform shock prime-mover and moderate shock load to the driven machine Gear ratio (mG) Varies 3 Design factor (nd) Varies 1.75 Tooth system Crown, straight bevel gears Straddle mounting One members straddle-mounted Crowned teeth conditions Larger uncrowned teeth Pressure angle (pn) 200 Tooth count Use within the range of 20 to 32 Design decisions Module (mm) 4 mm Face width (mm) 36 to 44 Quality number (QV) 8 Pinion materials Core and case hardened, Carburized and case hardness, Grade 2 Gear materials Core and case hardened, Carburized and case hardness, Grade 1 Hardness HBP = 475; HBG = 525

Q5 Design Straight bevel gear mesh for shaft centerlines that intersect perpendicularly with the following data Priori design Function Load (kW) 11 Speed (rpm) 924 Temperature (0C) 270 Pinion Life, NL (Cycles) 19232 Reliability 98.5 % Overload factor Uniform shock prime-mover and moderate shock load to the driven machine Gear ratio (mG) Varies 3 Design factor (nd) Varies 1.75 Tooth system Crown, straight bevel gears Straddle mounting One members straddle-mounted Crowned teeth conditions Larger uncrowned teeth Pressure angle (pn) 200 Tooth count Use within the range of 20 to 32 Design decisions Module (mm) 4 mm Face width (mm) 36 to 44 Quality number (QV) 8 Pinion materials Core and case hardened, Carburized and case hardness, Grade 2 Gear materials Core and case hardened, Carburized and case hardness, Grade 1 Hardness HBP = 475; HBG = 525

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

XY=11 By examine the parameters given, evaluate the maximum power-transmitting capacity, based on AGMA bending strength for both gears.
A pair of gears with 20° full-depth teeth are to transmit 15hp at 1750 rpm of the 4-in pinion; velocity ratio desired is about mw= 4; intermittent service. Use a strength reduction factor of about 1.4, with the load at the tip and teeth carefullycut. A.Determine the diametral pitch, B. face width, C. and tooth numbers if the material is cast iron, class 25
For each problem demonstrate your answer using autocadd software. 10.2 For the gear pairs given below and meshing at their correct center-to-center distance, determine whether any interference is present. Assume that the addendum is 1/P in each case. (spur gear) 10.21. 25° involute gears having 30 and 60 teeth. (P = 4)
power (N)=9.9kw Input speed (n1)=2350rpm Distance between centers (a)=168mm Total distance between Ave B bearings=440mm module(m)=3mm question 1 Calculate the conversion rate and output cycle
A pair of spur gears is to be designed for a compressor operating at 300 rpm, driven by a 9 kw, 1200 rpm electric motor. Centre distance between the axes of gears shafts is 250 mm. Starting torque of the motor can be taken as 40% extra on the rated torque. Both pinion and gear are made of steel with out=750 N/mm2.Teeth are of 20° pressure angle full-depth involute. If factor of safety is 2, specify dimensions of gears and recommend surface hardness of gears. 0.912, Y = T[0.154 – 1 What is effective factor of safety?
Q12:- Two involute gears of 20° pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is 2.0. The module= 5 mm and the pitch line speed is 120 cm/sec and assuming the addendum as standard and equal to one Find:- (a) the angle turned through by when one pair of teeth is in mesh and (b) the maximum sliding velocity. module.
Q5:- The particulars of a pair of spur gear are:- (a) gear ratio=(1/10), (b) center distance3D 660 mm approximately, (c) power transmitted%3D 500 kW, (d) speed of the pinion= 1800 rpm, (e) teeth are of involute form with pressure angle= 22.5°, (f) the addendum= 1 module and (g) the permissible normal force between teeth is 200 N/mm of gear width. Find :- (a) the nearest standard module if no interference to occur, (b) the number of teeth on each wheel and (c) the necessary width of pinion and gear.
1.Please design a pair of spur gears in the milling machine. It is known that power input is 7.5kW, Ni 1450r /min, and the %3D transmission ratio is required to be u = 2.08. F1. If there is slight impact, the supplementary conditions for trial design of this pair of gears: primary selection k = 1.8, number of smaller gear teeth Z1 = 26. The allowable stress and factors for material %3D is: [0]= 600 MPa, [o„]z= 599 MPa, [0,]ı= 220 MPa, [0,]= 213 MPa. E=1.693, Z, =1898/mpa Z„ = 2.5 K =1.25 Ky =1.1 K K =1.2 На K =1.35 Y =2.65, Y = 2.28 Y =1.58 Y =1.76 %3D Fa2 Fal sa1
A 17-tooth 20° pressure angle spur pinion rotates at 1800 rev/min and transmits 4 hp to a 52-tooth disk gear. The diametral pitch is 10 teeth/in, the face width 1.5 in, and the quality standard is No. 6. The gears are straddle-mounted with bearings immediately adjacent. The pinion is a grade 1 steel with a hardness of 240 Brinell tooth surface and through-hardened core. The gear is steel, through-hardened also, grade 1 material, with a Brinell hardness of 200, tooth surface and core. Poisson's ratio is 0.30, Jp = 0.30, JG = 0.40, and Young's modulus is 30(10°) psi. The loading is smooth because of motor and load. Assume a pinion life of 108 cycles and a reliability of 0.90, and use YN = 1.3558N-0.0178, ZN = 1.4488N-0.023. The tooth profile is uncrowned. This is a commercial enclosed gear unit. (a) Find the factor of safety of the gears in bending. (b) Find the factor of safety of the gears in wear. (c) By examining the factors of safety, identify the threat to each gear and to the…
p sa 15. A straight bevel gear pair has the following data: 50; P¿ 10; and 20° pressure angle. If the gear pair is transmitting 3.5 hp, compute the fore- es on both the pinion and the gear. The pinion speed is 1250 rpm. The face width is 0.70 in. Compute the bend- ing stress and the contact stress for the teeth, and specify a suitable material and heat treatment. The gears are driven by a gasoline engine, and the load is a conveyor provid- ing moderate shock. Assume that neither gear is straddle nounted. N₂ No = 25; No J (M
Let Module 5 (m = 5) for a given mutual spur gear pair; Strength, Wear Load, Static Load and Dynamic Show if the conditions for load control are met? For pinion gear:Gear material strength Steel 2k = 900 N / mmSpeed: 1400 rpmd1 = 90 mmZ1 = 18 teethVery precise workmanshipHardness: BHN (Brinell Hardness Number) 400Gripping angle: 20 (full depth involute).It will transfer 22 kW of power For large gear:Gear material strength Steel k = 900 N / mm2d2 = 360 mm Acceptance and Table values: Value depending on tooth width: K = 4 (best value will be taken) Peripheral speed: V = 6 m / s Deformation coefficient: C = 171 kN / m Lewis factor: y = 0.102 Stress fatigue coefficient: k = 2553 kN / m2 Gear wheel width: b = 62 mm
A 100 × 50 × 25mm steel block is subjected to a hydrostatic pressure of 5 MPa. The Young's modulus and Poisson's ratio of the material are 150GPa nd 0.2 respectively. The change in the volume of the block in mm³ is