The particulars of a pair of spur gear are:- (a) gear ratio=(1/10), (b) center distance= 660 mm approximately, (c) power transmitted= 500 kw, (d) speed of the pinion= 1800 rpm, (e) teeth are of involute form with pressure angle= 22.5°, (f) the addendum= 1 module and (g) the permissible normal force between teeth is 200 N/mm of gear width. Find :- (a) the nearest standard module if no interference to occur, (b) the number of teeth on each wheel and (c) the necessary width of pinion and gear.

The particulars of a pair of spur gear are:- (a) gear ratio=(1/10), (b) center distance= 660 mm approximately, (c) power transmitted= 500 kw, (d) speed of the pinion= 1800 rpm, (e) teeth are of involute form with pressure angle= 22.5°, (f) the addendum= 1 module and (g) the permissible normal force between teeth is 200 N/mm of gear width. Find :- (a) the nearest standard module if no interference to occur, (b) the number of teeth on each wheel and (c) the necessary width of pinion and gear.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Find the minimum shaft diameter (dmin) of the gear system given the dimensions and load values. A…

Q: A 17-tooth 20° pressure angle spur gear rotates at 1800 rev/min and transmits 4 hp to a 52-toot…

A: dp=NpPd=1710=1.7 indG=5210=5.2 inV=πdp.np12=π×1.7×180012=801.1 ft/min

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: (h) To find : The output speed. Given : The reduction ratio is : ζ=2.32. The module is : m=2 mm.…

Q: A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure…

A: We have to solve above question Given data Pitch diameter =50mm Power =3kw Angular velocity =200…

Q: Q.7 A pair of parallel helical gears consists of a 20 teeth pinion mashing with a 40 teeth gear. The…

Q: 1 A Q 1. When J is fixed: NA – No -72 N, – No Figure 4. schematic diagram of epicyclic gear…

Q: Find the design calculations of the gears box ,has (3)three speeds, Which is transmitted the power…

A: Given Data: The number of the tooth in gears are Z1=8, Z2=32 and Z3=64. The speed of 8 tooth gear…

Q: The particulars of a pair of spur gear are:- (a) gear ratio=(1/10), (b) center distance=D 660 mm…

A: Let pitch radius of gear and pinion be 'R' and 'r' respectively and module of pinion/gear be…

Q: Q4: The reverted gear train shown in Fig.(1) has the following data, • Circular pitch Pc=0.4…

A: Note: As per Bartleby guidelines only the first three sub-parts are to be solved. Please upload…

Q: If a pinion having 20 teeth transmit the power to the gear shaft having 40 teeth, the gear ratio of…

A: If a pinion having 20 teeth transmit the power to the gear shaft having 40 teeth, the gear ratio of…

Q: What is the transmitted load exerted by the pinion on the gear? Report your answer in lbf.

A: Given:Pinion Np=17 teeth, Gear Ng=52 teeth, Pressure angle∅=20∘ Power H=4 hp Diametral pitch Pd=10…

Q: campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km=…

Q: Design a two-stage compound spur gear train for an overall ratio of approximately 17+ID:1. Specify…

A: overall ratio=17+0071=241

Q: A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth…

A: Answer: (a) Normal circular pitch: 0.4335 in (b) Normal diametral pitch: 7.2470 in (c) Axial pitch:…

Q: the aid of an appropriate diagram and labelling, discuss the gear and belt trains which each have an…

Q: (b) Determine the safe power which can be transmitted by a pair of helical gears, 20° full depth,…

A: Gears are the two rings having teeth on it which are meshed together to transmit the power. They are…

Q: Example: Design a compound gear train for an exact reduction ratio of 180:1 given: ϕ =20o Module:…

Q: A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure…

A: Given:Power=3 kWpitch diameter=50 mmangular velocity of gear=200 rad/spressure angle of…

Q: Q5:- The particulars of a pair of spur gear are:- (a) gear ratio%3(1/10), (b) center distance%3D 660…

A: Given that the gear ratio is 10 Distance between the two gears, D = 660mm Therefore, R + r = 660mm…

Q: 3. A double-threaded right-handed worm gear transmit 15-hp at 1150 rpm. The pitch of the worm is…

Q: (b) Solve the base pitch, centre distance, whole depth and contact ratio of a gear with the given…

Q: Q4: The reverted gear train shown in Fig.(1) has the following data, •Circular pitch Pc=0.4 teeth/mm…

A: Givencircular pitch PC=0.4 teeth/mmT1=15T2=30T3=20N1=150rpm

Q: ExJA 20° straight-tooth bevel pinion having 14 teeth and a diametral pitch of 6 teeth/inch drives a…

Q: ral p

Q: A parallel helical gearset consists of a 21-tooth pinion driving a 63-tooth gear. The pinion has a…

Q: The particulars of a pair of spur gear are:- (a) gear ratio=(1/10), (b) center distance%3D 660 mm…

A: Given : G = TG / TP = DG / DP = 10 L = 660 mm P = 500 kW = 500 × 1000 W NP = 1800 r.p.m. φ =…

Q: 1.Please design a pair of spur gears in the milling machine. It is known that power input is 7.5kW,…

A: Given : P = 7.5 kW N = 1450 rpm u = 2.08 To find : Design pair of spur gears Note : some values are…

Q: A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth…

A: (a) Normal circular pitch: 0.43354 in (b) Normal diametral pitch: 7.24637 teeth/in (c) Axial pitch:…

Q: Q4: The reverted gear train shown in Fig.(1) has the following data, • Circular pitch Pc=0.4…

A: Given data: - The circular pitch is Pc = 0.4 teeth/mm. The number of teeth on gear one is T1 = 15.…

Q: A compound spur gear train with teeth as indicated in the figure with a module of 12mm and a…

Q: There are two pairs of closed soft tooth surface spur gears A and B, Parameters of A: modulus m =…

A: Two parts of spur gears-For Gear A-modulus, m=2mmAccuracy oftwo pairs of gear is = grade 8.

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Q5:- The particulars of a pair of spur gear are:- (a) gear ratio=(1/10), (b)
center distance= 660 mm approximately, (c) power transmitted3D
500 kw, (d) speed of the pinion= 1800 rpm, (e) teeth are of
involute form with pressure angle= 22.5°, (f) the addendum= 1
module and (g) the permissible normal force between teeth is 200
N/mm of gear width. Find :- (a) the nearest standard module if no
interference to occur, (b) the number of teeth on each wheel and
(c) the necessary width of pinion and gear.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

p sa 15. A straight bevel gear pair has the following data: 50; P¿ 10; and 20° pressure angle. If the gear pair is transmitting 3.5 hp, compute the fore- es on both the pinion and the gear. The pinion speed is 1250 rpm. The face width is 0.70 in. Compute the bend- ing stress and the contact stress for the teeth, and specify a suitable material and heat treatment. The gears are driven by a gasoline engine, and the load is a conveyor provid- ing moderate shock. Assume that neither gear is straddle nounted. N₂ No = 25; No J (M
A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5; Np = 20 teeth; carefully cut teeth; intermittent service; Kf= 1.45. A. Determine the diametral pitch, B. face width, C. and tooth numbers if the pinionis to be made of phosphor gear bronze (SAE 65, Table AT 3
(b) Solve the base pitch, centre distance, whole depth and contact ratio of a gear with the given parameters: Pa= 6, 20 degree pressure angle, 19-tooth pinion is meshed with a 77-tooth gear. 1. honano aean --. . -a..k hooi sohuch (c) Solve the contact ratio of a gear when the base pitch, P, is the same length of action, Z in Question Q2(b). [Selesaikan nisbah sentuh gear apabila jarak benang asas, Ps adalah sama Panjang Tindakan, Z dalam Soalan Q2(b).] If this gear (Q2(b)) is a one of the component needed for designing a compound gear train with ratio at 150:1, design the gear. [Jika gear ini adalah salah satu komponen yang akan digunakan untuk merekabentuk 'train' kompaun gear pada nisbah 150:1, rekabentuk gear ini. (d)
(a) Two involute gears of _pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is_. If the pitch expressed in module is 5 mm and the pitch line speed is_m/s, assuming addendum as standard and equal to one module, find : 1. The angle turned through by pinion when one pair of teeth is in mesh 2. The maximum velocity of sliding. D=30 G= 2 V=1.4m/sec
A spur gear reducer is to transmit 4 kW at 1500 rpm of the pinion of cast steel ( So=138 MPa). The gear is made from phosphor bronze (So=83 MPa). The velocity ratio is 3.5 to 1.0. Assume a pressure angle of 20°. Design the gears for strength only.
Draw a front section and profile for a worm and gear in an interlocking position according to the following data: 1- Center distance (center distance = 50 mm) 2- The outer diameter of the worm = 32 mm %3D 3- The step diameter of the worm = 26 mm 4- The root diameter of the worm = 20 mm 5- The width of the face = 22 mm 6- The length of the worm = 54 mm 7- The diameter of the worm shaft = 16 mm %3D 8- The length of the shaft Worm = 45 mm on each side 9- The diameter of the gear hole = 24 mm 10- The diameter of the hub = 42 mm 11- The width of the hub = 10 mm on one side 12- The type of key is the Gib With dimensions on the drawing
please send handwritten solution Q4 part d e f