1.Please design a pair of spur gears in the milling machine. It is known that power input is 7.5kW, Ni 1450r / min, and the %3D transmission ratio is required to be u = 2.08. F1. If there is slight impact, the supplementary conditions for trial design of this pair of gears: primary selection k = 1.8, number of smaller gear teeth Zl = 26. The allowable stress and factors for material is: [0.]= 600 MPa, [o„];= 599 MPa, [o,]ı= 220 MPa, [o,];= 213 MPa. E-1.693, Z =1898/mpa Z, = 2.5 K =1.25 K, =1.1 K=Kf =1.2 %3D %3D K =1.35 Y =2.65, Y =2.28 Y =1.58 Y =1.76 %3D Fal %3D Fa2 sal %3D sa2

1.Please design a pair of spur gears in the milling machine. It is known that power input is 7.5kW, Ni 1450r / min, and the %3D transmission ratio is required to be u = 2.08. F1. If there is slight impact, the supplementary conditions for trial design of this pair of gears: primary selection k = 1.8, number of smaller gear teeth Zl = 26. The allowable stress and factors for material is: [0.]= 600 MPa, [o„];= 599 MPa, [o,]ı= 220 MPa, [o,];= 213 MPa. E-1.693, Z =1898/mpa Z, = 2.5 K =1.25 K, =1.1 K=Kf =1.2 %3D %3D K =1.35 Y =2.65, Y =2.28 Y =1.58 Y =1.76 %3D Fal %3D Fa2 sal %3D sa2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.A pair of helical gears are designed to transmit 15 kW. The teeth are 20° stub in diametral plane and have a helix angle of 45°. The pinion runs at 10 000 r.p.m. and has 80 mm pitch diameter. The gear has 320 mm pitch diameter. If the gears are made of cast steel having allowable static strength of 100 MPa; determine a suitable module and face width from static strength considerations and check the gears for wear, given Ous = 618 MPa.
A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.
Don't give handwritten
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm². A0a& ENG 1222/20 nere to search
pls expalin to me step by step and write clearly. i will rate your answer immediately thanks
Helical Gears, Bevel Gears, and Wormgearing 2
If a pinion having 20 teeth transmit the power to the gear shaft having 40 teeth, the gear ratio of this system is 0.5. Select one: O True O False Stress concentration factor is defined as the ratio of the lowest stress or nominal stress in the component to the highest stress any where in the same component. Select one: O True O False A radial ball bearing fitted on to the shaft of a refinery vessel is subjected to axial load of 3340.8 N, take the service factor(K;) as 1.5. The equivalent dynamic load acting on the bearing will be . O 10022.40 O 1670,40 O 2505.60 O 5011.20 The outer diameter of muff is calculated as 81.2 mm. The shaft diameter of muff coupling is . mm. O a. 39.60 O b. 34.10 O c.61.38 O d. 26.80
(b)A pair of straight bevel gears has a velocity ratio of 2:1. The pitch circle diameter of the pinion is 80 mm at the large end of the tooth.A5KW power is supplied to the pinion which rotates at 800 rp.m. The face width is 40 mm and the pressure angle is 20. Calculate the tangential ,radial and axial components of the resultant tooth force acting on the pinion
A straight bevel gear pair has the following data: Np 25; NG = 50: P, = 10: 20° pressure angle. If the gear pair is transmitting 3.5 hp, compute the forces on both the pinion and the gear. The pinion speed is 1250 rpm. The face width is 0.70 in. Compute the bending stress and the contact stress for the teeth, and specify a suitable material and heat treatment. The gears are driven by a gasoline engine, and the load is a conveyor providing moderate shock. Assume that neither gear is straddle- mounted.
A pair of 20 pressure angle bevel gears of N , = 30 and N2 = 60 has a module m of 8.5 mm at the outside diameter . Determine the power capacity of the pair , using the Lewis and Buckingham equations . The gears have face width of 70 mm , K , = 1.5 , and the pinion rotates at 720 rpm . The gears are made of steel SAE 1040 and hardened to about 200 Bhn Hi sir this design machine
Q.8 A pair of helical gears in which teeth on pinion are 20 and on gear are 30, the normal module is 5 mm and normal pressure angle is 20°. The helix angle is 30°. The pinion is provided 5 kW at 720 rpm. Determine various forces on the teeth.
i need clear ans by hand and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛