The input speed of the worm shaft is 1200 rpm The worm wheel is made of phosphorbronze (sand cast), while the worm of casehardened carbon steel 10C4. The gear box for the worm gears has an effective surface area of0.25 m2. A fan is mounted on the worm shaft to circulate air over the surface of the fins. The coefficient of heat transfer can be taken as 25W/m2° C. The permissible temperature rise of the lubricating oil above the atmospheric temperature is 45° C. The coefficient of friction is 0.035 and the normal pressure angle is 20°. Calculate the power transmitting capacity based on thermal considerations.

The input speed of the worm shaft is 1200 rpm The worm wheel is made of phosphorbronze (sand cast), while the worm of casehardened carbon steel 10C4. The gear box for the worm gears has an effective surface area of0.25 m2. A fan is mounted on the worm shaft to circulate air over the surface of the fins. The coefficient of heat transfer can be taken as 25W/m2° C. The permissible temperature rise of the lubricating oil above the atmospheric temperature is 45° C. The coefficient of friction is 0.035 and the normal pressure angle is 20°. Calculate the power transmitting capacity based on thermal considerations.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An industrial fan running at 600 rpm is driven by a 25-kW, 960 rpm, induction motor. The pulley mounted on the motor shaft is 270 mm. Center to center distance is 1.5 meters and use f = 0.35. Determine the minimum angle of wrap in rad.
A multiple clutch has to transmit 90kW from an engine running at 3500 rpm. Clutch lining outer diameter is 200mm and inside diameter is 160mm. Spring pressure on clutch is 170kPa and it's coefficient of friction is 0.28. a)Calculate the minimum clamping force required b) Calculate the no. of clutch plates.
Example: An automotive single-plate clutch with twe of friction Surfaces, transmits a 300 N-m to- pairs rque at 1500 rp.m. The inner and outer diameters of the friction disck are 170 and 270 mm The cofficient of friction is 0-35. The normal for- ce on the friction Surfaces is exerted by nine helical Compre ssion springs, so that the clutch is always engia- ged. The clutch is dis engaged when the external force Further Compresses (5) and the number of ac Five Coile are (6) The are made of patented and Cold-drawn steel respectively. the springs. The spring index is Springs wires of minimum tensile Stmength (MTS) (N/mm?)as Wive dia. 1 1-21-4 1.6 1-8 2 2.53 3.6445567 MTS, 1900 i2601817e0175017201640 1570 I510 1480 440 139013201260 NI mr The permissible shear stress for the wire is 30%. of the ultimate tensile strength, and (G-81370 Nimn). Design the springs and specily their dimensisns. Use this relatian to obtaine to the total normal fore required to transmit the torque. F= 4T where Dis…
3. Design Challenge: The wind turbine is designed to generate 2.5 MW of power with the blades rotating at 20 RPM. The large gear has 360 teeth and the small gear has 12 teeth. Design the high speed shaft to minimize weight. That is, choose a material (from your textbook) and cross-section dimensions such that the shaft won't yield, with a safety factor of 2.5, while keeping the shaft's weight to a minimum. Calculate the weight per meter of the shaft you designed. 2 Gear reducer High speed shaft Low speed shaft Generator
A gear box has an input speed of 1800 rev/min clockwise and an output speed of 400 rev/min The input power is 25kW and the efficiency is 90%. Compute the input torque the output power 3. the output torque
Torque in = 40nm Holding torque out = 896nm 8.Using your answers from the gear box above, and given that the input shaft has a diameter of 12 mm and the output shaft has a diameter of 15 mm, both shafts are made from aluminium. When this transmission system was operated, it failed. Identify the position where the failure occurred and the reason for this failure. Suggests improvements to the system to overcome the failure mode. The shear strength of aluminium is 207 MPa.
Disc brakes are used on vehicles of various types (cars, trucks, motorcycles). The discs are mounted on wheel hubs and rotate with the wheels. When the brakes are applied, pads are pushed against the faces of the disc causing frictional heating. The energy is transferred to the disc and wheel hub through heat conduction raising its temperature. It is then heat transfer through conduction and radiation to the surroundings which prevents the disc (and pads) from overheating. If the combined rate of heat transfer is too low, the temperature of the disc and working pads will exceed working limits and brake fade or failure can occur. A car weighing 1200 kg has four disc brakes. The car travels at 100 km/h and is braked to rest in a period of 10 seconds. The dissipation of the kinetic energy can be assumed constant during the braking period. Approximately 80% of the heat transfer from the disc occurs by convection and radiation. If the surface area of each disc is 0.4 m2 and the combined…
4. A double threaded worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is 0.75" and pitch diameter is 3". The pressure angle is 14.5 degrees and coefficient of friction is 0.12. Find the worm gear efficiency.
9.10 An aircraft engine drives a propeller through a reduction drive shown in Fig. 9.27. The gears 1, 2, 3 and 4 have 48, 27, 45 and 120 teeth respectively. Find the propeller speed in magnitude and direction if the engine makes 2500 r.p.m. Arm Propeller Engine 1
Two-stroke six-cylinder ICE has a cylinder bore of 4” and a stroke of 4”. If the engine is running at a speed of 1,500 rpm, what is the indicated horsepower of the engine? The mean effective pressure is 80 psi. Ans. 91 hp
In a transmission system 25 ° spur gears are used and the number of teeth on each gear is Np=25 and NG=50. Load is applied at the highest point of single-tooth contact. Power source is electric motor and the transmission system drives uniformly loaded conveyors. The overload factor, Ko is:
An electric motor drives a punch press with a flywheel and is running at 1200 rpm. The torque of the punch press is as follows: a. 0-(10000+10) at first 45deg b. goes to zero for next 45deg c. 0-(6000+10) at next 45deg d. goes to zero for the remainder of the cycle. Employing a Cf of 0.2, a solid steel disc with density of 0.283 lb/in^3, and a thickness of 2 in, determine the flywheel diameter in meters.