The inner radius of clutch plate is 100mm and the outer diameter of the clutch plate is 400mm. what is the effect on the value of the mean radius when the inner radius is increased by 50% from the original value for the uniform wear criteria. Select one: O a. Decrease O b. Increase O . Constant O d. Double the value

Q: (Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X .A 40 .B 40lb .C 4lb .D 40N

A:

Q: The region bounded by the parabola x = y² and y = x2 revolved about the y-axis to generate a solid.…

A:

Q: Q1 A horizontal beam BC is subjected to uniformly distributed load, w and at the same time it is…

A: For solution refer below images.

Q: 400N 200 Z00 N さ

A: Given Data :

Q: Write the four different types of Resultant Loadings?

A: Loading: The loading on the beam or any members is the load acting on a beam under which beam…

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 2 m Find the angle theta. a = 5. b = 3. 1m 1m D

A:

Q: A plastic rod AB of length L = 520 mm has a diameter d, = 30 mm as shown in Figure Q2(b). A plastic…

A: For the given composite bar it is required to determine: (1) Total elongation of the bar when P = 15…

Q: Determine all furce mem bers of truss Shown the

A:

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: In the engine system shown, the lengths of the connecting rode (that is the length of BD) and the…

A:

Q: Find The curevature points A,B,C,D form least to greatest

A:

Q: Determine the position of the neutral axis of a curved bar subjected to flexure by a couple shown in…

A: The position of the neutral axis of a curved bar subjected to flexure by a pair must be…

Q: Is 2.0cm3 of aluminum same as 2.0cm3 of lead

A: According to the given data, the volume of the aluminum object is 2.0 cm³  and the volume of the…

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

A:

Q: Determine the x-y and n-t components of the 39-kip force F acting on the simply-supported beam. F =…

A:

Q: What is the resultant force?

A: Let us consider that an object has two forces acts on it. These forces are  10 N to its right.  50…

Q: 250cm+10m

A: Given Data : 250cm+10m

Q: (Determine the (f_x ) when force 80 N and angle 30° on the axis (X .A 69N .B 69.28lb .C 69.28N .D…

A:

Q: Write the equation that relates applied stress to local maximum stress.

A: Stress concentration factors are generally used to relate applied stress to local maximum stresses.…

Q: Question (2): The length of the-in.-diameter steel wire CD has been adjusted so that with no load…

A:

Q: Part A - Construction of Mohr's circle for the state of stress For the element shown, construct…

A: Given Data

Q: Express the quantity 254,998m in mm.

A: To convert meter quantity into millimeter one must be familiar with the no. of mm exist in one…

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A:

Q: Find the center of gravity of the wire.

A: The centroid, when referring to a solid item, denotes the geometric center or the location where the…

Q: G Determine the equillalent. tiffness for the dreegreem

A: Solution:

Q: //// // R R J3 Js Jy J. J8 R lt)

A: given; mass of block=mweight of block(w)=mgforce=F

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: If this were to be written how would it look like?

A: Geometric Symbol – This symbol is most useful and shows the position of the dimensions. Diameter…

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.