A spur gear is available having a diametral pitch of 4 teeth/in, a 2 inch face, 20 teeth, and apressure angle of 20° with full depth teeth. The material is AISI 1020 steel (S, = 30 kpsi).Using a design factor of na= 2.0 based on yield strength, calculate the horsepower that canbe transmitted through this gear having cut teeth at a speed of 1400 rev/min.Show all calculations. Do not convert to SI units.%3!

the term moderate applications seems to imply that the gear can be rated by using the yield strength…

pitch of 4 teeth/in, a 2 inch face, 20 teeth, and a pressure angle of 20° with full depth teeth. The material is AISI 1020 steel (S, = 30 kpsi). Using a design factor of ne =2.0 based on yield strength, calculate the horsepower that can be transmitted through this gear having cut teeth at a speed of 1400 rev/min. Show all calculations. Do not convert to SI units

pitch of 4 teeth/in, a 2 inch face, 20 teeth, and a pressure angle of 20° with full depth teeth. The material is AISI 1020 steel (S, = 30 kpsi). Using a design factor of ne =2.0 based on yield strength, calculate the horsepower that can be transmitted through this gear having cut teeth at a speed of 1400 rev/min. Show all calculations. Do not convert to SI units

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pinion and gear are running in mesh. The gear pair has a diametral pitch of 6. has 24 teeth, what is the corresponding pitch diameter of the pinion? 2 in (A) (B) (C) 3 in 4 in (D) 5 in (E) 6 in
A 20 degree-pressure-angle, 22-tooth spur gear has a diametral pitch equal to 5. Calculate the dedendum in mm
Please answer the question in details
Find the gear ratio, circular pitch, base pitch, pitch diameters, pitch radii, center distance, addendum, dedendum, whole depth, clearance of a gearset with the given parameters. A diametral pitch is 6 teeth per inch, 20°-pressure-angle, 19-tooth pinion and a 37-tooth gear. Assumptions: The tooth forms are standard AGMA full-depth involute profiles.
p sa 15. A straight bevel gear pair has the following data: 50; P¿ 10; and 20° pressure angle. If the gear pair is transmitting 3.5 hp, compute the fore- es on both the pinion and the gear. The pinion speed is 1250 rpm. The face width is 0.70 in. Compute the bend- ing stress and the contact stress for the teeth, and specify a suitable material and heat treatment. The gears are driven by a gasoline engine, and the load is a conveyor provid- ing moderate shock. Assume that neither gear is straddle nounted. N₂ No = 25; No J (M
A 35 kW motor running at 1200 rpm drives a compressor at 780 rpm. The arrangement is made through a 90° bevel gearing arrangement. The pressure angle of teeth is 14.5°. The allowable static stress for both pinion and gear are 85 MPa. Determine the number of teeth on the gear, face width, addendum, dedendum, outside diameter and slant height, thickness of tooth. Also check your design from the standpoint of wear. Take surface endurance limit as 690 MPa and modulus of elasticity as 89 kN/mm2.
What is the minimum clearance allowed for meshing spur gears with diametral pitch of 20? The spur gear has 25 teeth.
A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5; Np = 20 teeth; carefully cut teeth; intermittent service; Kf= 1.45. A. Determine the diametral pitch, B. face width, C. and tooth numbers if the pinionis to be made of phosphor gear bronze (SAE 65, Table AT 3
A parallel helical gear set of 19 tooth pinion is driving a 57 tooth gear. The helix angle of 20 degrees while the normal pressure angle is 14.5 degrees and the normal diametral pitch of 10 teeth/inch. If the pinion is rotating at 1800rpm and transmits 50hp, find the normal force. Please answer in detailed solution.
Please help me finding this question. Power = 6 kW
What is the solution for this?
A spur gear reducer is to transmit 4 kW at 1500 rpm of the pinion of cast steel ( So=138 MPa). The gear is made from phosphor bronze (So=83 MPa). The velocity ratio is 3.5 to 1.0. Assume a pressure angle of 20°. Design the gears for strength only.