Can I have a written solution Q3(a)For the digital control system given in Figure 3, by adding phantom samplers toshow that the z transfer function of the closed-loop system is given byC(z)R(z)G(z)1+ G(z) H₁H₂(z)+R(s)G(s)C(s)H₂(s)H₁(s)Figure 3(b)The analogue compensator5s + 1D(s) =0.4s +1is implemented digitally with sampling period 0.2 seconds to control the depth ofa submarine system. Use the pole-zero mapping method to find a digitalapproximation to the analogue compensator.

solution for part(a).Solution for part(b).

Answered: Q3 (a) For the digital control system…

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter11: Thermostats, Pressure Switches, And Other Electric Control Devices

Section: Chapter Questions

Problem 23RQ

See similar textbooks

Similar questions

Q6)This Multiple choice questions from electronics lab course &just write for me final answer ,It easy for you.
An op-amp comparator in a firing circuit can produce waveforms at the output of up to 28 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +14 to -14 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is 5.92 volts, the delay angle (in degrees) would be:
9. The input to an inverting Op-Amp differentiator circuit is shown in figure-4. The differentiator has an input capacitor of value C = 0.47 µF, and a feedback resistor of value Rf = 2.2 k2. Graph the differentiator output waveform. 0- Ims] Figure-4: Input signal to the Op-Amp differentiator circuit
What are the barkhausen criteria for oscillations in a open loop circuit?
If in the oscillator block diagram shown in Figure, = 0.1V, A = 100 and m = 0.01, then the circuit will. V₁ mVo Voltage Gain A Feedback Circuit V
please answer all thanks !
This is a practice question from my Introduction to Electronics course. Please talk me through the process. Thank you for your assistance.
The time period of an astable multivibrator with a duty cycle of 25%, a feedback factor of 75% and a time constant of 1 ms, is -- - S.
Q6 A closed-loop control system is represented by block diagram as shown in Figure Q6. R(s) + C(s) 2 Kp (s + 1) (s + 6) Figure Q6 (i). Develop the transfer function and estimate the proportional controller gain Kp so that the undamped natural frequency of the closed-loop system is 4 rad/sec. (ii). Estimate the proportional controller gain Kp and the maximum percentage overshoot so that the damping ratio of the closed-loop system is 0.7. (iii). Compute the steady-state errTor output for step response input r(t) = 4u(t) and controller gain Kp = 2.
The type of the feedback in this circuit is: VDD M5 M6 X Vino M3 Select one: MAH Iss Laser WI a. shunt-series feedback lout O b. shunt shunt O c. series-series feedback O d. series-shunt feedback RM
with comments on the output for better understanding Thank you
a) Negative feedback circuits such as the Schmitt trigger are used to solve noisy scenarios in comparator circuit applications. Using circuit diagrams and waveforms, explain clearly how this is achieved. b) An LM35 temperature sensor has the following transfer function: Vout 10mV °C x Temp (°C) Design an electronic circuit to turn on an LED rated at 5V whenever the temperature falls below 85°C. The circuit should use a comparator, a few resistors and the LM35 temperature sensor. You should demonstrate by calculation and by simulation in multisim or proteus that your circuit works correctly. Only screenshots are required for simulation no files needed.

SEE MORE QUESTIONS

Recommended textbooks for you

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning