Over string of 3-0 transmission line has (3) insulators and Ce = 0.12 C. If the voltage between the steel pinof the first insulators and metal gap of the last insulator is 33 kV. find:1. The voltage distribution across the insulators and efficiency.2. The new voltage distribution and efficiency if number of insulators increases one.

Step 1: Setting up foundation for problem:Voltage closest to conductor is V4. For n insulators in a…

Answered: Over string of 3-0 transmission line…

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 14RQ

See similar textbooks

Similar questions

i) Calculate V1 and V2 for the voltage across the string insulator having phase voltage of 33kV for transmission line using details tabulated in the Table 3(a). Table 3(a) Type of Insulator Shunt Capacitance between each unit 0.1 C String to junction Self -Capacitance of each insulator ii) With the help of a suitable schematic diagram and necessary theoretical explanation, illustrate how to improve the efficiency of the suspension insulator.
State the main constituent elements of electrical cables, as well as the materials from which they may be made. Describe the following designations: H05VV-U 1G4 mm? and LSXAV 3x16 mm?.
In an outdoor substation the three bus-bar conductors are supported by units of post type insulators. Each unit consists of a stack of 3 pin type insulators fixed one on the top of the other. The voltage across the lowest insulator is 15kV and that across the next unit is 12kV. Estimate: ratio of mutual to self-capacitance i. the bus-bar voltage of the substation. Efficiency across the string of insulators ii. iii.
Question 3 a. Some materials exhibit the property of superconductivity under certain conditions. State what is meant by superconductivity and explain the required conditions for the material to become superconducting. b. The diagram below shows the cross-section of a cable consisting of parallel filaments that can be made superconducting, embedded in a cylinder of copper. copper cylinder filament The cross-sectional area of the copper in the cable is 2.28 x 10-7 m². The resistance of the copper in a 1.0 m length of the cable is 0.075 N. Calculate the resistivity of the copper, stating an appropriate unit. State and explain the what happen to the resistance of the cable when the embedded filaments of wire are made superconductive? i.
The diameter of an ACSR conductor is 1.162 inches. The steel core has 7 strands of diameter 0.1291 inches each. If Aluminum strands have the same diameter as that of a steel strand, the number of Aluminum strands is: O A. None of choices are correct O B. 36 O C. 74 O D. 54 O E. 45
Ferromagnetic materials have this characteristic. A. A relative permeability slightly less than one. B. A relative permeability slightly greater than one. C. A very high resistivity. D. A high relative permeability.
8. Parallel conductors must be installed in sizes no smaller thanA. 1/0.B. 2/0.C. 750 kcmil.D. 4/0.
The resistance of wire increases from 40 – ohm at 20 0C to 50 – ohm at 70 0C. Find the temperature coefficient of resistance at 0 0C.
Q. 16. The best gas mixture for circuit breakers of the following is: C. Air and Sf DN2 and hydrogen A. Air and hydrogen B. Sf6 and N₂
Discuss typical structure of the modern electrical grid. Include all elements and provide short description of their role in the system
H. W.: The cost of a 2-core feeder cable, including installation is (90 a + 20) per meter and the interest and depreciation charges are 10 per cent. The cable is 2 km in length and cost of energy is 4% per unit. The maximum current in the feeder is 250 A and the demand is such that the current copper loss is equivalent to what would be produced by the full flowing for 6 months. If the resistance of a conductor of 1 square cm and 1 km length is 0.173 Q, calculate the most economical cross-sectional area.
A 2-wire d.c. ring distributor is 300 m long and is fed at 240 V at point A. At point B, 150 m from A, a load of 120 A is taken and at C, 100 m in the opposite direction, a load of80 A is taken. If the resistance per 100 m of single conductor is 0-03 Q, find :(i) current in each section of distributor(ii) voltage at points B and C * IA 150 m 120 A в A 240 V 100 m I - 120 IA - 200 80 A

Recommended textbooks for you

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning