Q20. The shape of a liquid's meniscus (concave/convex) is controlled by? A) the relative magnitudes of cohesive forces in the liquid and adhesive forces between the liquid and its container B) the volume and mass of the liquid C) the amount and strength of hydrogen bonding in the liquid D) the type of material the container is made of E) the boiling and freezing points of the liquid

Q20. The shape of a liquid's meniscus (concave/convex) is controlled by? A) the relative magnitudes of cohesive forces in the liquid and adhesive forces between the liquid and its container B) the volume and mass of the liquid C) the amount and strength of hydrogen bonding in the liquid D) the type of material the container is made of E) the boiling and freezing points of the liquid

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

2) N2= Ni(acac)2 C Ph JCS P1, 1984, 261
Please short answer
C-14 --> ____________ + N-14
Above is a fractional distillation set up. Name five things wrong with the set up.
Questions 15 through 20 pertain to the following medication formula: Here is the formula a pain and inflammation reducing ointment. Methyl salicylate (sp gr = 1.167) 60 mL Lidocaine 4% (w/w) Tween:Span mix (1:4 mix) Polypeg Base 10 g QS to 0.5 kg You receive an order to make 3 solid ounces of this product. Answer the following questions pertaining to producing 3 solid ounces of the product. 15. Volume of methyl salicylate, in milliliters. 16. Weight of lidocaine in grams. 17. Weight of Tween in milligrams. 18. Weight of Span, in milligrams. 19. Weight of Polypeg base, in grams. 20. What is the final concentration of methyl salicylate, as a percent concentration (w/w)?
< STARTING AMOUNT X A brine solution is 3.50% NaCl by mass. Given that its density is 1.071 g/mL , determine the quantity of liters of solution that contains 5.00 moles of NaCl 5.00 ADD FACTOR 0.1 *( ) 3.50 10 35.45 Question 29 of 33 1.071 0.01 8.03 x 1022 1000 100 ANSWER 7.80 22.99 0.0156 L solution g NaCl/mL g solution mL solution kg solution g NaCl/g solution 58.44 6.022 x 1023 0.0780 moles of NaCl mol NaCl RESET 0.001 2 1 g NaCl 1.56
2- 185.0 mL of .12 M C2H5NH2 with 285.0 mL of 0.21 M C2H5NH3CI Kb(C2H5NH2) = 5.6×10^-4 Express your answer using two decimal places. pH = ?
01-5a Match the generic formula to its generic name. CnH2n+2 [Select] CnH2n-2 [Select] C6H6 [Select] соно CnH2n [Select] <
1. Certified Reference Material (CRM), GSS-5, is certified to contain 40.67 ± 3.33 mg/kg of Ni in soil. An analysis of the CRM gives values of 40.39, 41.98, 43.64, 44.38, and 45.96 mg/kg. Determine the tcalc. value and determine if your results differ from the expected results at the 90 % confidence level?
Please answer as much as I can
30 20 10 From the procedure 2. Assemble the simple distillation apparatus as generally shown in Figure SD.1 in the lab manual, ensuring that the thermometer bulb is aligned at, or slightly below, the Y in the distillation head. Each ground joint is greased by putting three or four stripes of grease lengthwise around the male joint and pressing the joint firmly into the other without twisting. 3. Attach a water condenser to the distillation head. 4. Remember, water goes in the bottom and out the top. Attach a clamp holder to the end of the drain tube to keep it weighted in the drain. Turn water to a trickle. If it is slowly draining, it is high enough. Begin a low flow of water through the condenser. 5. Place the set up on a heating/stir plate. 6. Turn on the hot plate to start heating the solution. Monitor the temperature and the boiling of the solution throughout the distillation process. 7. Record the temperature of the distillate when the first drops are recovered. 30.0 8. Adjust…
Make a dilution series to get to 1:100. Start with making 1:10 dilution by adding 1mL of sample and 9mL of diluent, now continue the series to get to 1:100. The formula you may use is V1D1=V2D2