Q2. Consider the single-phase transformer circuit shown below. Transformer ratings and reactances are: Transformer A : 200 kVA, 250 / 750 V , X= 0.10 p.u. : 100 kVA , 900 / 300 V , X = 0.15 p.u. Transformer B The transmission line can be represented as a series impedance Zine = 0.4 + j 0.6 Q. Choose a base of 200 kVA, 250 V in the voltage source ( V, ) circuit. (a) Draw the impedance diagram for this circuit, with all impedances in per unit. (b) Find the load voltage in per unit and in volts when the source voltage is V.=120° pu. (c) Find the transmission line current (IL) in amperes. transmission line A (Zi-0.4 + j0.6 N) В "line V Z=0.5 + j0.2 N Lee Lee

Q2. Consider the single-phase transformer circuit shown below. Transformer ratings and reactances are: Transformer A : 200 kVA, 250 / 750 V , X= 0.10 p.u. : 100 kVA , 900 / 300 V , X = 0.15 p.u. Transformer B The transmission line can be represented as a series impedance Zine = 0.4 + j 0.6 Q. Choose a base of 200 kVA, 250 V in the voltage source ( V, ) circuit. (a) Draw the impedance diagram for this circuit, with all impedances in per unit. (b) Find the load voltage in per unit and in volts when the source voltage is V.=120° pu. (c) Find the transmission line current (IL) in amperes. transmission line A (Zi-0.4 + j0.6 N) В "line V Z=0.5 + j0.2 N Lee Lee

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single-phase transformer has 180 and 45 turns, respectively, on its primary and secondary windings. The corresponding resistances are 0.2422 and 0.076 S2, respectively. Determine the equivalent resistance a. in primary terms, and b. in secondary terms.
A load impedance of (200+j0) ohm is to be matched with a 50 ohm transmission line using a quarter wave transformer. What will be the value of the characteristic impedance of the quarter wave transformer.
3. A non-ideal 1-phase transformer has turns ratio 5:1 with 120Vac primary. The primary impedance is 1 + j1 Ohms, and the secondary impedance is 0.2 + j0.2 Ohms. Assume the core impedance (R0 and X0) can be neglected. A resistive load of 12 Ohms is connected to the secondary. What is the primary current magnitude? What is the secondary voltage magnitude? What is the efficiency of this transformer with this load?
No-load operation and short circuit tests were performed on three-phase, 50 Hz 480/220 delta / Y connected transformer. In these testsThe line voltage, line current and three-phase total power have been measured from the high voltage windings and the test results are below.pictures. 100 A DC current when 1.08 V DC voltage from non-transferable software is applied to the low voltage windingshas attracted.Find the single phase equivalent circuit parameters of this transformer.idle test:Voltage: 480V Power:114w current: 0.71Ashort circiut test:V: 10v P: 78w c: 18.3a
A conventional phase transformer given in the figure will be connected as an autotransformer in two different ways. Each For a connection, find the input and output powers by drawing the connection. a) Connection of 1220 / 220V autotransformer b) 1000 / 1220V autotransformer connection
3) A three-phase transformer of 60 kVA (three-phase power), 13200/480 V (line A line) in delta-strella connection has a resistance of 0.02 PU and a reactance of 0.08 PU. For this transformer, calculate: a) The voltage regulation at full load and F.P. 0.85 in delay. (b) The regulation of voltage voltage to full cargo and F.P. Unitarian. c) The voltage regulation at full load and F.P. 0.85 in advance.
2. Given three identical ideal single-phase transformers with each rated at 100KVA and 7kV/3.5kV, they are connected as a three-phase transformer bank. The three-phase transformer has high voltage side connected in delta and the low voltage side is connected in wye. A three-phase 200KVA, wye connected load is connected at the low voltage side of the transformer. Calculate the following: a. Rated line-to-line voltage on each side b. Line current on each side of the transformer
When the transformer is loaded in a balanced fashion up to its nominal rating (10 MVA), calculate the high side line-to-line phasor voltages (ab, bc, ca). and low side phasor voltages both line-to-line and line-to-neutral (ab, bc, ca, a, b,c). as a reference for calculations the low side A line to neutral voltage is 7620V at an angle of 0 degrees when the transformer is at rated power. The transformer has the following characteristics: V: 138kV delta high side/ 13.2 kV wye low side 9% impedance X/R ratio of 20
a single-phase transformer serves a 7.2kw resistive loadlocated 200 ft from the transformer. each conductor from the transformer to load has an impedence of (0.78+j0.052) ohms per 1000ft. if the voltage at the load terminal is 240v, the magnitude of the voltage (v) at the transformer secondary is most nearly:
30-kVA, 2200/220-V, 50-Hz distribution transformer is tested for efficiencyand regulation as follows :O.C. test( Low voltage side ) : 220 V 4.2 A, 148 W S.C. test ( Low voltage side ) : 86 V 10.5 A, 360 W 1-The working current and resistance component of no-load are.........amper , .........ohm * 2-Efficiency at full-load and half the full-load at 0.8 p.f. lagging current. * 3-Equivalent resistance referred to primary & referred to secondary..........ohm , ..........ohm * 4-Regulation of transformer at 0.5 p.f. lagging current * 5-Equivalent reactance referred to primary & referred to secondary..........ohm , ..........ohm * 6-The magnetizing current and reactance component of no-load are.........amper , .........ohm *
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. A capacitor bank of -j0.171 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: O A. 7360 V O B. 6.2 kV O C. 12750 V O D. 4806 V O E. None of the other choices are correct
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.