A 50 KVA, 4,400/220 V transformer has r1 =3.54 ohms r2=0.009 ohms, x1 =5.2 ohms and x2 =0.15 ohn Find: a. the equivalent resistance as referred to the primary and secondary b. the equivalent reactance as referred to both primary and secondary d. equivalent impedance as referred to primary and secondary.

A 50 KVA, 4,400/220 V transformer has r1 =3.54 ohms r2=0.009 ohms, x1 =5.2 ohms and x2 =0.15 ohn Find: a. the equivalent resistance as referred to the primary and secondary b. the equivalent reactance as referred to both primary and secondary d. equivalent impedance as referred to primary and secondary.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In single phase transformer, if the secondary turns N2 is greater than the primary turns N1, then what is the relation between V2 and V1? O a. V2 = V1 O b. V2 > V1 O c. V1 < V2 O d. V2 < V1
Solve it quickly please
- A Transformer has primary windings as Np = 750 and secondary windings as Ns = 125. Its secondary voltage is Vs = 36V and output power of the transformer is PN= 3200W. The value of loses powers are Pcu = 43W and Pfe = 29 W. The resistance of loads are RLI = 1,250 and R12 = 0,88Q. (Pcu and PFE will be considered to be approximately the same in different load values.) Determine the following values in the circuit: Primary winding N, turns Secondary winding Ng turns Primary current Magnetic Flux, Secondary IsL s current ISL1 'Isl2 Primary voltage Secondary voltage RL1 R12 Transformer Core (a) the primary voltage Vr, (b) the secondary load currents ISLı and Isl2 if the transformer is rated at RLI and R12, (c) the resulting secondary power PSL, (d) the resulting primary power PPl, (e) the primary load current IPL, (f) efficiency nL
Q2/A/ What are the conditions for satisfying parallel operation of single phase transformer? Deduce an expression for the load shared by the two transformers in parallel when the transformers have equal voltage ratio? Prove your answer. B/ A 50 KVA, 2300/230 V, 60 11z transformer has a high voltage winding resistance of 0.650 and a low-voltage winding resistance of 0.0065 2. Laboratory tests showed the following results: Open circuit test: V = = 230 V, I =5.7A, P = 190 W Short circuit test: V-41.5 V, I-21.7 A, P-No wattmeter was used. 18 (2) Compute the value of primary voltage needed to give rated secondary voltage when the transformer is connected as a step-up one and is delivering 50 KVA at a power factor of 0.8 lagging. (b) Compute the efficiency under conditions of part (a).
A short circuit test performed on a 25 KVA 2300/230 V transformer gives the measured value of the resistance as 0.8 Q and 0.009 Q on the two sides of the transformer. The total equivalent resistance in Q referred to LV side will be
30-kVA, 2200/220-V, 50-Hz distribution transformer is tested for efficiencyand regulation as follows :O.C. test( Low voltage side ) : 220 V 4.2 A, 148 W S.C. test ( Low voltage side ) : 86 V 10.5 A, 360 W 1-The working current and resistance component of no-load are.........amper , .........ohm * 2-Efficiency at full-load and half the full-load at 0.8 p.f. lagging current. * 3-Equivalent resistance referred to primary & referred to secondary..........ohm , ..........ohm * 4-Regulation of transformer at 0.5 p.f. lagging current * 5-Equivalent reactance referred to primary & referred to secondary..........ohm , ..........ohm * 6-The magnetizing current and reactance component of no-load are.........amper , .........ohm *
The maximum efficiency of a 200KVA, 6000/230volt, 50HZ, single phase transformer occurs at half load and is 95% at unity power factor. What is the full load efficiency at 0.7 power factor?
The value of A =436, B=57, C =7
Which of the following statements is true about an ideal transformer? O It changes the magnitude of DC signals. O It converts DC signals into AC signals. O It converts AC signals into DC signals. O It changes the magnitude of AC signals. hp