Q2: Select a tension member is to consist of two C10 channels and two PL 1/2 x 11, arranged as shown in Figure below to support the service loads, PD= 200 k and PL= 320 k. The member is assumed to be 30 ft long and is to have four lines of 3/4-in Ø bolts. 30 degrees Assume U= 0.85. All steel will be A36.

Q2: Select a tension member is to consist of two C10 channels and two PL 1/2 x 11, arranged as shown in Figure below to support the service loads, PD= 200 k and PL= 320 k. The member is assumed to be 30 ft long and is to have four lines of 3/4-in Ø bolts. 30 degrees Assume U= 0.85. All steel will be A36.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.2.1P

See similar textbooks

Similar questions

Asap pls
STEEL ANALYSIS full solution and final answer to 4 decimal places pls
3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates of the same width with half the thickness by 24mm diameter bolts, as shown. The rivet holes have a diameter of 2mm larger than the rivet diameter. The plate is A36 steel with yield strength F,-248MPa and ultimate strength F,-400MPa. a. Determine the design strength of the section. b. Determine the allowable strength of the section 24mm 30mm
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 2-inch-diameter bolts. Assume that A₂ = 0.75An. Ae 1 2 Determine the design tensile strength for LRFD. Determine the allowable strength for ASD. CIVIL ENGINEERING - STEEL DESIGN AL Section 2L5 x 3 x 516 LLBB
A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x 6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer
A C8 x 11.5 is connected to a gusset plate with 7/8 inch diameter bolts as shown in Figure P3.2-3. The steel is A572 Grade 50. If the member is subjected to a dead load and live load only, what is the total service load capacity if the live to dead load ratio is 3? Assume that Ae=0.85An. Use LRFD and ASD.
A 16 mm thick tension member is connected by two 6.25 mm spliced plates as shown. The tension member carries a service loads of dead load of 110 kN and a live load of 100 kN. 40, 80 , 40 , 40, 80 40 1625 mm 16 mm 1625 mm Fy 248 MPa Fu = 400 MPa Diam. of bolts = 16 mm Fnv = 300 MPa O Determine the nominal strength for one bolt due to shear. O Determine the nominal strength for one bolt due to bearing strength of the connection. ® Determine the number of bolts required for the connection.
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t
A tie member of a roof truss consists of 21SA 100 x 75 x 8 mm. The angles are connected by fillet weld as shown in figure on either side of a 10 mm gusset plate and the member is subjected to a factored pull of 450 kN. Take size of weld as 6 mm and connections are made in workshop. [Use Fe410 grade of steel] 75 m L. C. = 31mm 16A (100 x 75 x 8) mm Choose the nearest correct statements: L1 = 390.5 mm L1 = 195.25 mm Correct Option L2 = 87.75 mm Correct Option L2 = 175.5 mm
A 2L 3 x 2 x ¼ LLBB tension double angle, A36 steel is subjected to a dead load of 12 kips and a live load of 36 kips. It is attached to a gusset plate with a line of 3/4-inch diameter bolts through the long legs. Does this member have enough stamina? Assume Ae= 0.85 in. Use LRFD.
WideFlange Section: W 16x67