10 Select a W shape for the tension member shown. The member shown will be connected between two plates with 8- 22 mm o bolts. The service loads are: DL= 975 KN and LL= 120 KN. The member length is 6.75 m. Use A36 steel (F,= 250 MPa and F,= 400 MPa). Consider all limit states including block shear. Use ASD. Answer 37.5 mm - thickness of plate tp=8 mm 37.5 mm each 75mm 37.5175 mm75mm 75mm375 mm Tmm

10 Select a W shape for the tension member shown. The member shown will be connected between two plates with 8- 22 mm o bolts. The service loads are: DL= 975 KN and LL= 120 KN. The member length is 6.75 m. Use A36 steel (F,= 250 MPa and F,= 400 MPa). Consider all limit states including block shear. Use ASD. Answer 37.5 mm - thickness of plate tp=8 mm 37.5 mm each 75mm 37.5175 mm75mm 75mm375 mm Tmm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem For the frame shown, design the maximum permissible value of P with a factor of safety of 2.5. Design the maximum permissible value of P based on the following conditions: ✓ Ultimate tensile strength of each member CD is 300 ksi Ultimate shear strength of the bolts in A, C, E, and F is 200 ksi ✓ Ultimate bearing strength of member BDE is 150 ksi ✓ Ultimate bearing strength of the support plates is 250 ksi Members CD and BDE have cross-sectional dimensions of 5 in x 3 in (the larger dimension is the width). The diameters of the bolts are as follows: A and B - 1.5 in: C and D-2 in E and F - 1 in. 1.5 in. thick Support Plates -2 ft + D 3 ft B 2 in thick Support Mate Solution Step 1. Identify the conditions for design. Stress normal stress in each member CD, OCD shear stress in bolt A, TA shear stress in bolt C, T shear stress in bolt E, T shear stress in bolt F, T bearing stress on member BDE due to: bolt B, BDE-B bolt D, OBDE-D bolt E, OBDE-E bearing stress on support plates at…
A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used is A36, Fy= 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine: a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20.------ b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20.-------- I M20 bolts- 210 mm -Tension Plate
J 6 The cast iron bearing seat in the picture is bolted to the steel beam of the ceiling bracket and supports the gravity load. Use M20 coarse thread ISO class 8.8 bolts with a thickness of 3.4 mm The steel washers are placed under the bolt head and nut. The flange of this bracket is 20 mm thick, the shaft The elastic modulus of the bearing is 135 GPa. (a) Assuming this is a permanent joint and the fasteners are lubricated when assembled, find the required wrench torque. (b) If the gravity load is 15 kN, try to find the load factor n of the design.
SOLVE FOR1 HR
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO
Design the reinforcements of the given T beam below. bf=900mm bw=420mm tf-120mm d=550mm d'=80mm fc'=34MPa fy=415MPa USE NSCP 2015 A.Mu = 1300kN-m, As = mm2 B.Mu = 1800kN-m, As = mm2, As' = mm2
Please correct answer otherwise dislike
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm
Five M20 8.8/ bolts are used in the connection between a beam and a column. Both sides of the cleat plate are welded to column using fillet weld (Manual metal arc AS4855 B-E43XX) with size of 5 mm. The design force transferred from beam to column is 300 kN. The cleat plate has thickness of 12 mm, fy = 300 MPa, and fü = 360 MPa. Determine the unit stress sustained by the weld