A PL x 7 tension member is connected with three 1-inch-diameter bolts, as shown in Figure P3.2-1. The steel is A36. Assume that A. = A, and compute the following. a. The design strength , Pu based on gross area b. The design strength, Pu based on effective area PL x 7 3/8" O o 7" Cross Sectional area of PL3/8x7

A PL x 7 tension member is connected with three 1-inch-diameter bolts, as shown in Figure P3.2-1. The steel is A36. Assume that A. = A, and compute the following. a. The design strength , Pu based on gross area b. The design strength, Pu based on effective area PL x 7 3/8" O o 7" Cross Sectional area of PL3/8x7

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

.
The T-shape shown in the figure is used as a tension member. Given that the gross area Ag = 2556 mm², tw = 10 mm, gross depth d = 220 mm and bolts are 16-mm-diameter, with Fy=345 MPa and Fu = 450 MPa, calculate the nominal block shear strength for combined tensile rupture and shear rupture. Write your answer to the nearest whole number in kN. Consider Ubs = 1.0 T 40 mm. +* 125 mm O 4@.75 mm O O O O
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
Determine the allowable strength of the figure as shown
Given: The L8x4x½ shown below is welded to the gusset plate by its long leg. L₁ = 10" and L₂ = 7.5". L₁ L₂ Determine the gross area. 5.80 in² Calculate the length of the connection. 8.75 Calculate the eccentricity of the connection. 0.854" Calculate the width of the connected element. Calculate the value of the shear lag factor. Calculate the effective net area. in² II
5 please help meee
Given the truss shown, solve the following. Use A36 steel and assume there are two lines of three 19 mm bolts in each flange. Hole diameter is assumed to be three mm more than the bolt diameter. Neglect the weight of the section. a.What is the capacity of member CG? b. Design member CG using a W section. c. What is the tensile capacity of the section for CG based on gross area? The following W Section were considered for the design: W10x33 W14x38 W8x40 W16x36 W10x39 W8x13 189 KN 1.50 HL B 145 KN 1.50 E + 137 KN 121 KN -3.00 + 12.00 3.00 154 KN + W4x13 W6x9 W10x12 200 KN -1.50 1.50 1 030 T 1.20 +2.40 0.60 L i 0.30
Design the reinforcements of the given T beam below. bf=900mm bw=420mm tf-120mm d=550mm d'=80mm fc'=34MPa fy=415MPa USE NSCP 2015 A.Mu = 1300kN-m, As = mm2 B.Mu = 1800kN-m, As = mm2, As' = mm2
A PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The diameter of the holes are 25 mm. The pitch and gage of the holes are 50 mm and 75 mm, respectively. The yield strength of the steel is 260 MPa while the ultimate tensile strength of the steel is 400 MPa. Determine the design (LRFD) tensile strength of the tension member in kN. Neglect block shear. H FO E. • D A В
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 2L5 x 3 x16 LLBB Determine the allowable tensile strength for ASD. Select one: а. 52.1 b. 104.2 c. 87.8 d. 43.9
A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x 6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer
Please answer the problem attach image below, Using NSCP 2015, show your solution.