Q2:(33 Marks)Design FBD for manufacturing system where a conveyor belt is used to move a cart through a tunnel forprocessing. The process begins when a worker presses a start push button located at the start of the conveyor.Once the start push button is pressed, the cart moves forward along the conveyor belt and enters the tunnel.When the cart reaches the end of the tunnel, it stops automatically and remains in place for 10-minutes tocomplete a required operation, such as cooling or drying. After the 10-minute delay, the cart automaticallyreturns to the starting point where the worker is stationed. The system then waits for the worker to press thestart push button again, at which point the process is repeated.Start PBOStop PBOLSI0LS 2Motor

Question Summary: Design a Function Block Diagram (FBD) for a manufacturing system using a conveyor…

Answered: Q2: (33 Marks) Design FBD for…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a mulching plant uses a large motor to shred logs into small pieces. It takes the chipper motor 10 seconds to reach operational speed. A conveyor feeds the chipper hopper with large logs. to avoid jams, the chipper motor must be running 10 seconds before any logs are fed in from the conveyor. when the stop pushbutton is pressed, the conveyor immediately stops, but the chipper continues to run for 10 seconds after the conveyor stops (in case a log is still in the chipper). Use start stop pushbuttons to operate the system.
The intermediate between mechanical energy and electrical energy in electrical machines is... a) A DC battery b) Responsible for energy flow from the rotor to the stator in case of generator mode c) The magnetic field storing energy temporarily d) Responsible for energy flow from stator to rotor in case of generator mode Next Page Page 1 of 4 Submit Quiz O of 4 questions saved
The following information is given for a 300kW, 600V, long shunt compound DC generat or, shunt field resistance is 75 ohms, armature resistance 0.01, brush resistance is 0.011 ohrms, series field resistance is 0.012 ohms and the divert or resistance of 0.036 ohms.When the machine is delivering full load; a. Draw the circuit diagrarn b. Calculate the voltage and C Power generated by the armat ure.
3. i. Write the working principle of Permanent Magnet Moving Coil instrument mention the importance spring used. ii. Explain how a single PMMC instrument can be used as ammeter and voltmeter.
SOLVE THE PROBLEM, SHOW YOUR COMPLETE SOLUTION AND MAKE SURE THAT THE FINALS ANSWERS ARE IN 4 DECIMAL PLACES.
Look carefully at the figure and answer the following questions. For your answers choose between on the right, on the left and it is zero; there are no more options. (a) When the switch is “open” i. Where does the current flow in the battery? ii. Where is the magnetic flux going in the bar on the left? iii. Where does the magnetic flux go in the bar on the right? iv. Where does the current flow in the resistor?
What is turnover torque and when occur؟
Determine the commutator pitches for the following simplex-wave wound armature: (a) 75 segments, four poles; (b) 229 segments, six poles; (c) 227 segments, eight poles. (Our lesson is DC GENERATORS in the subject ELECTRICAL MACHINE 1) (I NEED A CLEAN ANSWER AND SOLUTION. THANK YOU SO MUCH
A. The brushes used in a DC generator a) ride against the commutator segments. b) are made from material softer than the commutator segments. c) are generally marked Al and A2 d) all of the above B. A magneto is a DC generator that uses for its pole pieces. a) electromagnets b) permanent magnets c) either "a" or "b" d) neither "a" nor "b"
A)The left hand rule for a coil is such that if you were to hold a coil in your left hand with your fingers pointing in the direction of the electron flow, your thumb would point in the direction of thea) electron flow b) flow lines c) face of the north pole d) none of the above. B) What is a magnetic flux line?a) It is the space around a magnet or the space in which the magnetic forces act.b) It is the magnetic force that has a definite direction at all points along a curved line from the north to south pole.c) It is the ability of a magnetic material to be easily magnetized.d) none of the above C)It is believed that a magnetic material is .........a) consists of a single large magnetic molecule b) is composed of many tiny magnetic molecules c) consists of a single non-magnetic molecule d) none of the above
Create a short essay based on your own understanding and opinion about the question, “How does a dc generator work?”. Minimum of 150 words.
2.A. When machine losses are determined by the retardation method, it is necessary to know the machine'sA. ventilation requirements.B. resistance.C. moment of inertia.D. electrical input.2.B. If an aluminum field coil has a resistance of 120 ohms at 30 C, its corrected resistance at a temperatureof 75 C isA. 140.5 ohms.B. 141.2 ohms.C. 132.9 ohms.D. 133.3 ohms.

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS