Problem 10-3 Consider an FIR system defined by the difference equation below: y[n] = 2x[n] +4x[n − 1] + 2x[n − 2]. - - (a) Determine and sketch the impulse response h[n] of this system, i.e., determine the output when the input is 8[n]. (b) Determine and sketch the output of this system when the input is u[n], where u[n] is the unit step signal, i.e., u[n] = {{ 0 n<0 1 n≥0 (c) Determine and sketch the output of this system when the input is x[n] = u[n] — u[n — 4].

Problem 10-3 Consider an FIR system defined by the difference equation below: y[n] = 2x[n] +4x[n − 1] + 2x[n − 2]. - - (a) Determine and sketch the impulse response h[n] of this system, i.e., determine the output when the input is 8[n]. (b) Determine and sketch the output of this system when the input is u[n], where u[n] is the unit step signal, i.e., u[n] = {{ 0 n<0 1 n≥0 (c) Determine and sketch the output of this system when the input is x[n] = u[n] — u[n — 4].

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Electrical Engineering b) The figure shows the phase shift oscillator with Opam with R; = 12 kn and feedback resistor of R; = 36 k2 that need to operate at 2.5 kHz. Select the capacitor C and resistor R to obtain the 2.5 kHz. Verify your design, making a simulation in a specialized software (Multisim) showing the input and output signals and the frequency of the output signal. +Vcc R; Amplificador operacional -VEE
Ex. 453. G(s)=k(s+96)/(s(s+88)) is the FTF of a unity-feedback closed-loop system. Sketch the root locus with respect to k. Determine the number of asymptotes (N), number of root loci (M), the breakaway point (s=B) and the entry point (s=E). Answers: N,M,B, and E. ans:4
Autesave For revision session ) - Protected View Saved to this PC P Search (AltQ Natasha Keery File Home Insert Draw Design Transitions Animations Slide Show Record Review View Help Record Present in Teams eShare O PROTECTED VIEW Becrefles from the Intenet.can contain vinnen. Unles you need te edit safr to stey in Protected Vie. Enable iditing 14 Example 15 For the comparator circuit shown below, a a sinusoidal input signal with a peak voltage (Vp) of 5 V and a frequency of 1 Hz is applied to the non-inverting terminal. Assuming that the signal frequency is well below the slew rate limit, describe and draw what would be the comparator output. Assume values of +Vcc as +10V and -Vec as -10 V, with the corresponding output saturation voltages of +V of +9 V and -V of -9 V. 16 17 18 19 Sde 1of 24 English united Kingdom ENG 014 210/2022
4. a) Find the complete solution for the difference equation y[n] – 0.9y[n-1] = x[n] with the input x[R]= (-1/4)"u[n] and initial condition y[-1]= 1. b) An LTI system has an impulse response h[n] and input x[n] displayed in Figure 2 below. (b.i) Apply the method of convolution by superposition to find and sketch the convolution output y[n] of the system. (b.ii) Determine and sketch the step response of this LTI system.
Problem-3: Consider the negative feedback block diagram given in Figure-3. a) Find the value of the output y(t) at time t = Cg assuming an impulse reference input (i.e. r(t) = 8(t)). R(S) s+C6 Figure-3 1 s² + C₁ →Y(s)
81 A unity feedback closed loop second order system has a transfer function- and is excited by a s+0.6s +9 step input of 1 unit. The steady state error of the output is
Determine the transfer function of the system ( G(s) ), the response of the system ( Q(s) ), and q(t)
Please don't provide handwritten solution ..... What would be the impulse response of the circuits
The op-amp in the circuit depicted can swing rail-to-rail, has a gain-bandwidth product of 20 MHz, and a slew rate of 0.5 V/μs. The feedback resistors are R1 = 10 kn and R2 = 4 ko, and the amplitude of the sinusoidal voltage source (i.e. Vpeak) is x = 1.2 V. Does the output (vo) consist of a single sinusoid, or is the waveform distorted? Explain your reasoning, which may include some short equations. 5 V x20⁰ V w = 1k rad/s 20 + -5 V R10 O O Vo
Answer the following Draw, Illustrate and label your schematic diagram before solving the problem. 3. ) A Colpitts Oscillator circuit having two (2) capacitors of 37 nF and 350 nF respectively are connected in parallel with an inductor of 30 mH. Determine the frequency of oscillations of the circuit, the feedback fraction and draw the circuit. These might help as a guide in answering the question.
Please show work
Determine the new gain