*please use pen and paper to show work (thank you!!!)* Design a synchronous binary up-counter using 4 negative edge-triggered JK flip-flops provided with a clock. The states (sequences) 1100, 1001 and 1000 are considered as unused states. (i) Draw the state diagram of the counter. (ii) Build the counter’s state table showing the synchronous inputs of the JK flip-flops as well. (iii) Using Karnaugh-maps, find the minimal sum-of-products (SOP) form of the equations for the inputs to the flip-flops; assume the next states of the unused combinations to be <don’t care states=. (iv) Draw the logic circuit of the counter.

please use pen and paper to show work (thank you!!!) Design a synchronous binary up-counter using 4 negative edge-triggered JK flip-flops provided with a clock. The states (sequences) 1100, 1001 and 1000 are considered as unused states. (i) Draw the state diagram of the counter. (ii) Build the counter’s state table showing the synchronous inputs of the JK flip-flops as well. (iii) Using Karnaugh-maps, find the minimal sum-of-products (SOP) form of the equations for the inputs to the flip-flops; assume the next states of the unused combinations to be <don’t care states=. (iv) Draw the logic circuit of the counter.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Task 1: Custom Sequence Counter Using JK Flip Flop, Design a counter circuit that cycles through the sequence: 0, 5, 4, 6, 1, 7, and repeats. Follow these steps: a) State Diagram: Draw a state diagram representing the sequence. Each state should be expressed as a binary number. b) State Table: Create a state table for the counter, detailing current states, next states, and outputs. c) Flip-Flop Input Equations: From the state table, derive the input equations for the flip- flops. Treat any unused states as don't-care conditions. d) Simplification using K-maps: Use Karnaugh maps to simplify the flip-flop input equations. Optionally, verify your simplifications using Multisim. e) Circuit Diagram: Draw the circuit diagram. Task 2: 3-bit Up/Down Counter Using Flip Flop of your choice, design a 3-bit counter that counts up or down based on an input signal X. The counter should behave as follows: Initial State: On powerup, the counter starts at 0. Count Up (X=1): Sequence progresses through…
Design a modulo-5 ripple (asynchronous) down-counter with D flip-flops and draw the corresponding logic circuit. (i) Build the state diagram and extract the state table(ii)Draw the logic circuit(iii) What is the maximum modulus of the counter?
9 Using D flip-flops, (a) Design a counter with the following repeated binary sequence: 0, 1, 2, 4, 6. (b) Draw the logic diagram of the counter. (c) Design a counter with the following repeated binary sequence: 0, 2, 4, 6, 8. (d) Draw the logic diagram of the counter.
6) For IC 7493, answer the following questions: a) What is the maximum count length of this counter? b) This is a (ripple, synchronous) counter. c) What must be the conditions of the reset inputs for the 7493 to count? d) This is a(an) (down, up) counter. e) The IC 7493 contains (number) flip-flops. f) What is the purpose of the NAND gate in the 7493 counter?
9. Analysis of Synchronous Counters, in the following figure, write the logic equation for each input of each flip-flop. Determine the next state for state 010,011,100,111 as Q2Q1Q0 sequence. FF0 FFI FF2 Ko K, K2 CLK
(c) For each of the following parts, fill in the respective row of the timing diagram shown in Figure 5. (i) Find the input for a rising-edge-triggered D flip-flop that would produce the output Q as shown in Figure 5. (ii) Find the input for a rising-edge-triggered T flip-flop that would produce the output Q as shown in Figure 5. Clock D Figure 5
Design a synchronous counter with the irregular binary count sequence shown in the state diagram in the nearby figure. Use (a) D flip-flops, and (b) J-K flip-flops. 6 4 2
3- Design a counter with a control input. When the input is high, the counter should sequence through three states: 10, 01, 11 and repeat. When the input is low the counter should sequence through the same states in the opposite order 11, 01, 10 and repeat.a) Draw the state diagram and state transition table.b) Implement the counter using D flip-flops and gates.
3.) The design size of the synchronous counter sequential (sequential) logic circuit. It will count from 0 to 9 and the son of your student number will not count decimals in two digits. A. List the process steps that you will apply in the design approach. Create the State Chart and State Chart. B. Design the sequential circuit using JK Flip-Flop. Explain each step. Show that it has performed the desired action. last digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
1)Design a 3-bit binary gray code up/down counter using J-K Flip Flops. Draw the state table, state diagram and draw the logic circuit.
Design a 4-bit counter that counts in Excess-3 code. The counter should count to (6)10 and then restart. The counter should have a synchronous (not an asynchronous) active-high reset signal that resets the counter to "0'. You may use any logic gates/blocks learned in class and the constants 0' and 1'. Answer
You are asked to design a synchronous counter that will count the sequence 1 > 2>3>1. (a) Represent these decimal numbers in 2 bits binary numbers. (b) Write down the state table. (c) Find the functions for the next state of the state table using K-map. (d) Draw the circuit (You need to consider D flip-flops as memory unit).