Q1) The frame shown below is fixed at point Q and subjected to the axial load at free end in both direction x and y axis. Determine the actual stresses acting at points A and B, if (a) (Es/Ec) = 8, (b) %3D (Es/Ec) = 0.

Q1) The frame shown below is fixed at point Q and subjected to the axial load at free end in both direction x and y axis. Determine the actual stresses acting at points A and B, if (a) (Es/Ec) = 8, (b) %3D (Es/Ec) = 0.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. A force Q is applied to a rectangular member with a size of 3oomm x 450mm. Q is located 37-5mm left and 6omm north of the center of gravity and induces a stress of 1.75 MPa compression at point A. a) What is the axial load at Q in kN b) What is the stress induced at point C & D in MPa A B
Problem 7. [Concepts: Allowable stresses and factor of safety] Two aluminum rods AB and AC support a vertical load P. The allowable tensile stress for the aluminum is Gallow = 150 MPa. a) If P = 20 kN, determine the required diameters of the rods AB and AC. b) If the diameters of the rods AB and AC are 10 mm and 8 mm, respectively, determine the largest vertical force P that can be supported. U B
5. The beam ABCD with a rectangular cross section carries the loading shown in the figure. Determine the magnitude and location of the maximum bending stress in the beam.
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
The state of stress at a point in a member is shown on the element. Determine the principal normal stresses and their orientation and the maximum in-plane shear stress and their orientation. Draw Mohr’'s circle and Show results on properly oriented elements. -60 30 -50 40 -40 T-30 30 30 -20 40 30 -10 -60 -50 -40 -30 -20 -10 30 40 50 10 20 бо 10 20 30 40 50 60
A cantilever beam AB is loaded as shown in the Cross-section of the beam figure and the beam is supported with a cable BD. The beam's cross-section is rectangular as shown. It is known that the tension force in cable BD is 10.39 kN. Calculate the normal stress at point a, and calculate the shear stress at point c. Ignore the weight of the beam. 10cm 10cm +15cm+ 75cm B F-13.99KN 30cm 60cm 90cm
PROBLEM No. 2 The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A and C are stress-free. If a 20-kip load is applied, determine the vertical displacement in the bar at A and C that will cause a stress in the rod at C to be 50 ksi. Indicate the direction of movement. Use E = 29x106 psi for steel. (Provide FBD and movement diagram in your computation). A = 0.5 in.? 3 ft | A B D | 20 kips te 2 ft -→-- 2 ft -→l 4 ft 4 ft A = 0.75 in.²
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P = 1531 N, T = 4945 Nm, a = 0.87 m, b = 1.05 m, c = 0.77 m, w = 32 mm, and h = 77 mm .
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A B F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.
9. A single horizontal force P of magnitude 900N is applied to end D of lever ABD shown in the figure below. Knowing that portion AB of the lever has a diameter 36mm, determine a) the normal and shearing stresses on an element located at point H and having sides parallel to the x and y axes, b) the principal planes and the principal stresses at point H. 300 mm 120 mm y B H A 540 mm 36 mm P D
The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←