Q.3 water flows over a flat surface atupstream velocity U. A pump draws off waterthrough a narrow slit a volume rate of (m)m³/s per meter of the slit. Assumed fluid isincompressible and invicid.(a) Write the complex potential function ofthe combined flow.(b) Find the stream and potential functions ofthe flow.(c) Locate the stagnation point on the wall(point A).U(m) m³/s (permeter of lengthof slit)

Answered: Image /qna-images/answer/745aa841-f8dd-4421-b596-b11add25b932.jpg

Answered: Q.3 water flows over a flat surface at…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows over a flat surface at 4 ft/s, as shown in Fig. 5 . A pump draws off water through a narrow slit at a vol- ume rate of 0.1 ft/s per foot length of the slit. Assume that the fluid is incompressible and inviscid and can be represented by the com- bination of a uniform flow and a sink. Locate the stagnation point on the wall (point A) and determine the equation for the stagnation streamline. How far above the surface, H, must the fluid be so that it does not get sucked into the slit? 5- 4 ft/s 0.1 ftls (per foot of length of slit)
A 2-1/2 inch fire hose discharges water through a nozzle having a jet diameter of 1 inch. Thelost head in the nozzle is 5.76 percent of the velocity head in the jet. If the gage pressure atbase of nozzle is (a) 86 lb per sq in.: (b) 167 lb per sq in.: (1.1) compute the discharge ingallons per minute: (1.2) what is the maximum horizontal range to which the stream can bethrown, neglecting air resistance?
A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.
5- Water flows over a flat surface at 4 ft/s, as shown in Fig. 5 . A pump draws off water through a narrow slit at a vol- ume rate of 0.1 ft/s per foot length of the slit. Assume that the fluid is incompressible and inviscid and can be represented by the com- bination of a uniform flow and a sink. Locate the stagnation point on the wall (point A) and determine the equation for the stagnation streamline. How far above the surface, H, must the fluid be so that it does not get sucked into the slit? 4 ft/s 0.1 fts (per foot of length of slit)
... height Fire hoses used in major structural fires have an inside diameter of 6.40 cm. Suppose such a hose carries a flow of 43 L/s. The hose rises up 13.3 m along a ladder to a nozzle having an inside diameter of 3.00 cm. What is the starting pressure at the fire truck? Use p=1000 kg/m³ and g =9.8 m/s? Answer in KPa. No label, no unit, number only.
Please solve it with explanation.thx.
Pro er hydrant nozzle in Fig. 1 has inlet and outlet diameters, D₁ = 8 cm and D₂ 1.0 cm. Water at 20°C flows through the nozzle at 0.001 m³/s and exits to the atmosphere. The atmospheric pressure is 101.3 KPa. Neglect the weight of the piping and nozzle. Compute: a) The exit fluid velocity, V2, ( b) The inlet pressure, Pl c) The horizontal force which must be resisted by the = flange bolts S d) The moment acting on the flange neglect the weight of the hydrant and water 10 m 8 cm Fig. 1: Water hydrant 1
Q.5 a) In a 80 mm diameter pipeline an oil of specific gravity 0-8 is flowing at the rate of 0-0125 m^3/s. A sudden expansion takes place into a second pipeline of such diameter that maximum pressure rise is obtained. Find :(i) Loss of energy in sudden expansion,(ii) Differential gauge length indicated by an oil-mercury manometer connected between the two pipes. (iii) find the maximum pressure rise. (-
Q.2 Consider steady, laminar, incompressible fluid flow in a two-dimensional diverging channel as shown in the figure. The inclined walls of the channel are straight, and the fluid enters the diverging section with velocity V₁ = 40 m/s. Given H = 1 m, and assume unit width. (a) Determine an expression for the velocity component u as a function of position x along the H channel. (u does not depend on y.) (b) Determine an expression for the acceleration of the fluid in the x-direction. (c) An expression for the velocity component v (d) An expression for the acceleration in the y-direction V₁ L = 10H h(x) 4H
! MIN 1/1 米 4:22 PM O O 81% Find a relation between nozzle discharge velocity V2 and tank free surface height h as in figure below. Assume steady frictionless flow. HGL - II Open jet:
Make it Simple.
Read the question carefully and give me right solution according to the question

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS