5- Water flows over a flat surface at 4 ft/s, as shown in Fig. 5 . A pump draws off water through a narrow slit at a vol- ume rate of 0.1 ft’/s per foot length of the slit. Assume that the fluid is incompressible and inviscid and can be represented by the com- bination of a uniform flow and a sink. Locate the stagnation point on the wall (point A) and determine the equation for the stagnation streamline. How far above the surface, H, must the fluid be so that it does not get sucked into the slit? 4 fts 0.1 ft's (per foot of length of slit)

5- Water flows over a flat surface at 4 ft/s, as shown in Fig. 5 . A pump draws off water through a narrow slit at a vol- ume rate of 0.1 ft’/s per foot length of the slit. Assume that the fluid is incompressible and inviscid and can be represented by the com- bination of a uniform flow and a sink. Locate the stagnation point on the wall (point A) and determine the equation for the stagnation streamline. How far above the surface, H, must the fluid be so that it does not get sucked into the slit? 4 fts 0.1 ft's (per foot of length of slit)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 5- Water flows over a flat surface at 4 ft/s, as shown in Fig. 5. A pump draws off water through a…

A: Given that ; The speed of water flows are u=4 ftsec. The volumetric flow rate is 0.1 ft3sec.…

Q: A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see…

A: Fluid relative density = 0.88 PA = 150 KPa PB = 225 KPa ZA = 9.8 m ZB = 0 m

Q: A woman is draining her fish tank by siphoning the water into an outdoor drain as shown in the…

A: The area of the base of the rectangular tank is A and the height is hTherefore, the volume of the…

Q: Fluid flows into a junction at a flowrate Q, and exits via two pipes of equal diameter, as shown in…

A: We can answer up to 3 subparts so we will answer first 3. Please resubmit the question by specifying…

Q: A tank (contains a fluid of density=2370.7 kg/m3) stands on a frictionless cart (The cart is fixed)…

Q: Consider a desired pump operating condition which adds 35 psi at a flow rate of 500 gpa to water.…

A: Given data Pressure = 35 psi Flow rate = 500 gpm Density of water = 62 lbs/ft^3 Find the pump head…

Q: Suppose a u-bend is redirecting a flow of water. The water enters flowing to the right at 10 m/s.…

A: Given data:The velocity of water is The diameter of pipe is constant The pressure of the fluid is…

Q: has a layer of mercury under a layer of water. The mercury is flowing out through a frictionless…

Q: A submersible pump is to be selected for the installation on a newly drilled deep well. The static…

A: The total dynamic head of the water system determines the various head losses that the pump must…

Q: 2. An incompressible fluid flows past a stationary flat plate with uniform inlet profile and a…

A: Plate width = bControl volume height = Control Volume width = WInlet velocity = v0Outlet velocity,

Q: The characteristics for a pump are given in the table below. The pump is required to left water…

Q: Consider the fluid flow between two large plates at a distance L from each other. While the top…

Q: A horizontal pipe ends with a nozzle that discharges to the atmosphere. The pipe has adiameter of…

A: The objective of the question is to find the diameter of the nozzle required to obtain a jet with a…

Q: Fluid flows into a junction at a flowrate Q, and exits via two pipes of equal diameter, as shown in…

Question

5- Water flows over a flat surface at 4 ft/s, as shown in
Fig. 5 . A pump draws off water through a narrow slit at a vol-
ume rate of 0.1 ft/s per foot length of the slit. Assume that the fluid
is incompressible and inviscid and can be represented by the com-
bination of a uniform flow and a sink. Locate the stagnation point
on the wall (point A) and determine the equation for the stagnation
streamline. How far above the surface, H, must the fluid be so that
it does not get sucked into the slit?
4 ft/s
0.1 fts
(per foot of length of slit)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

02 h, are 12m. The pump efficiency is 79%, and the pump is driven by an electric motor. A pump moves water @10°C from a lake into a large, pressurized holding tank as shown. The flow rate, Q. is 375 L/min, and the piping system losses, 1) Sketch the setup (simple schematic is good), 2) label the z datum, and 3) identify and label the boundary conditions (P, V, and z) at 1 and 2 for use in a) the General Energy Equation (GEE). Provide values and units for the boundary conditions. Hint: For identifying good locations for boundary conditions, where are the velocities approximately zero? b) Calculate the head added to the fluid, h,, by the pump. Give your answer in units of m. Hint: Be careful with signs in manipulating the GEE. Show as many steps as you need to get your h, equation correct. Calculate the power added to the fluid by the pump in units of kW. () Determine the required electric motor size to drive the pump in units of HP. Prank = 200 kPa Holding Tank Air 6 m Pump Lake
Q.5 A pump circulates water through a closed pipe network connecting a water heater and a heating coil (heat exchanger) in a room. The total length of the pipe is 28 m and the diameter is 32 mm. There are six 90°-elbows and a globe valve in the network. The head loss through the water heater and the heating coil are 1.6 m and 1.2 m respectively. The water flow rate is 0.88 Ls!. The system uses schedule-40 steel pipes with threaded fittings. Calculate the (i) flow velocity and the unit pressure loss in the pipe. (ii) increase in head across the pump. (iii) power input to the pump if the efficiency of the pump is 70%.
Water is pumped between two reservoirs in a pipeline with the following characteristics; (d=275mm, L= 50m, = 0.02, minor loss is neglected. The pump performance curve is approximated by the equation: H,=21.5-6507 Where H, is in meters and Q is in m/s. Determine the discharge O and pump head /7 when two pumps in series are used for total static head (4Z=25m).
1. Water flows over a flat surface at 1.2 m/s, as shown in the figure. A pump draws in water through a narrow slit at a volumetric flow rate of 0.01 m/s per meter length of the slit. Assume that the fluid is incompressible and inviscid. 1.2 m/s a) Determine the location of the stagnation point on the H A wall (point A) (Ans: at x = 0.002653 m, y 0) b) Determine the equation of the stagnation streamline. (Ans: y = 0.002653 0 m (0 in radians)) c) How far above the surface, H, must the fluid in the uniform flow be so that it does not get sucked into the slit? (Ans: 0.0083345 m)
A pump is needed to drain an excavation at a construction site. The excavation has alength of 50m, width of 50m, and a depth of 4m. The surface of the water in the excavation lies at adepth, H=3m, from the top the of the excavation. An old, radial flow, 1000W pump is immediatelyavailable for use; however, the total pump-motor efficiency, e, is only 50%. Estimate the drawdown inthe excavation in the first 4 hours of pumping. Neglect the change in H with increasing time. Neglectany head loss in the hose/pipe connected to the pump. (Hint: utilize the Pout equation, consider analternative definition of discharge as a change in volume over a change in time). Assume a specificweight of 9.79kN/m 3 .
Please explain on how to get the theta, Qin and Qout. It should be theta = 54.2461 deg Q in = 0.0382 m3/s Q out = 0.0191 m3/s my professor said. but I don't have solution. used 9.807m/s² not 9.81.. thank you
A 5 cm diameter pipe takes off abruptly from a large tank and runs 8 m, then expands abruptly to 10 cm diameter and runs 45 m and next discharges directly into the open air with velocity of 1.5 m/sec. Compute the necessary height of water surface above the point discharge (Hint: losses in pipes in series concept).
Problem 4. (30') on a Water flows steadily through the reducing elbow shown below. The elbow is smooth and short. The effect of friction is small. The volume flow rate Q is 2.5 × 10-³ m³/s. The elbow horizontal plane (Z₁ = Z₂). Gravity direction is along z axis which is normal to paper. Below is the diagram of the elbow looking from above. Outlet is at atmospheric pressure 101325 Pa. Density of water is 1000 kg/m³. Find Pressure at inlet, P1 Supply pipe ↑ D = 45 mm ↓ y 1 Plan view Reducing elbow d = 25 mm
A pipeline of constant diameter 0.6m, with its centreline on a horizontal plane turnsthrough a horizontal angle of 75°. It carries water at a volumetric flow rate of 0.85m3/s.Calculate the horizontal components of force exerted on the pipe bend (in the originaldirection of water flow and perpendicular to this).
4) A constriction in a pipe will cause the velocity to rise and the pressure to fall at section 2 in the throat. The pressure difference is a measure of the flow rate through the pipe. The smoothly necked-down system shown in Figure is called a venturi tube. Find an expression for the mass flux in the tube as a function of the pressure change. (1) HGL 4²² (2)
I need the answer as soon as possible
An inflow to a turbine with a discharge of 20 m³/s leads to a ration speed of 150 rpm. The blades inlet edges have an angle of 120° to the direction of whirl. The outer diameter of the runner is 1.5 m and the runner inlet width is 1.0 m. 5. (a) To plot the velocity triangle at the blade outlet edge. (b) Assume design operating conditions and no velocity of whirl at outlet, calculate the power delivered by the runner. (c) The elevation difference between the head race and the tail race is 23 m and the head available to the turbine is 20 m, what is the hydraulic efficiency of the turbine and overall efficiency? (d) If a model of 1/10 full scale is constructed to operate under a head of 10 m, what must be its speed, power, water consumption and overall efficiency to run under the similar conditions to the prototype?