5- Water flows over a flat surface at 4 ft/s, as shown in Fig. 5. A pump draws off water through a narrow slit at a vol- ume rate of 0.1 ft³/s per foot length of the slit. Assume that the fluid is incompressible and inviscid and can be represented by the com- bination of a uniform flow and a sink. Locate the stagnation point on the wall (point A) and determine the equation for the stagnation streamline. How far above the surface, H, must the fluid be so that it does not get sucked into the slit? 4 ft/s 0.1 ft/s (per foot of length of slit)

5- Water flows over a flat surface at 4 ft/s, as shown in Fig. 5. A pump draws off water through a narrow slit at a vol- ume rate of 0.1 ft³/s per foot length of the slit. Assume that the fluid is incompressible and inviscid and can be represented by the com- bination of a uniform flow and a sink. Locate the stagnation point on the wall (point A) and determine the equation for the stagnation streamline. How far above the surface, H, must the fluid be so that it does not get sucked into the slit? 4 ft/s 0.1 ft/s (per foot of length of slit)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please help, will provide definitely helpful ratings for full solution. Thank u
Please assist me with this problem as soon as possible.
VII. Suppose water is leaking from a tank through a circular hole of area A, at it's bottom. When water leaks through a hole, friction and contraction of the stream near the hole reduce the volume of the water leaving the tank per second to cAp 2gh where c(0
3b
The discharge velocity is 49 m/sec and 227 mm water gage. The suction pressure is 48 mm water vacuum and velocity of 3 m/s. Calculate the fan total head in terms of water. Answer in cm.
A tank (contains a fluid of density=1239.6 kg/m3) stands on a frictionless cart (The cart is fixed) and feeds a jet of diameter 4 cm and velocity 6 m/s, which is deflected 0=35 degree by a vane. Compute the tension in the supporting cable. 6 m/s 35 deg -D= 4 m- Do = 4 cm Cable
(a) Suppose we have planned to design a hydraulic system.ln this aspect, the pump selection is to be finalized for a flow rate of 3907 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 4.4 m/s and 6.92 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines. (b) Write the significance of using minimum diameter pipelines in the hydraulic system. (a) Area of the maximum sized pipe diameter (in m?) (b) Area of the minimum sized pipe diameter (in m2) (c) The minimum sized pipe diameter (in m) (d) The maximum sized pipe diameter (in m)
Given: Two (2) identical pumps connected in parallel has the following data: Suction Pressure = 315 KPA Discharge Pressure = 220mmHg Suction Pipe Dia = 390mm Discharge pipe Dia = 405mm Velocity of Water = 6.0 m/s Solve: Total Head, Pump1 & 2 individual head and if Pump 2 is 9.5% less than Pump 1 and Q₁ = Total Flow Rate
3.
answer in complete solution
Ex (3): Consider the flow of water between two vertical parallel plates at 30 degrees Celsius. The distance between the plates, 2B, is small in comparison to the plates' length (l) and width (w). The plate on the left side is fixed, while the plate on the right is rising upward at a tiny velocity U. Given the length of the plates, the flow of water between them is considered to be laminar and fully developed. Find the shear stress profile of the flowing water using shell momentum balance method and sketch the profiles.
Q4: A 300 L/s of water flow through pipe Shown in figure (4). The pressure at entrance is 70 KPa. Calculate the force by fluid of sp.gr-0.9 on the bend if the volume of bend is 0.085 m³. (R= 8.55 KN) D₁=30cm D₂=20cm 6 Q4 1.5