5. Kerosene (sp.gr. = 0.88 ) enters the cylindrical arrangement as shown on the figure at section 1 at 0.08 /s. The 80 mm diameter plates are 3 mm apart. Assuming steady flow and unit weight of water is 9790 N/ m3 (a) Compute the inlet average velocity Va (b) Compute the outlet volume flux in m/sec (c) Compute the average velocity V2 assuming radial flow in mm/sec D-80 mm 3 mm 4 mm 4 mm

5. Kerosene (sp.gr. = 0.88 ) enters the cylindrical arrangement as shown on the figure at section 1 at 0.08 /s. The 80 mm diameter plates are 3 mm apart. Assuming steady flow and unit weight of water is 9790 N/ m3 (a) Compute the inlet average velocity Va (b) Compute the outlet volume flux in m/sec (c) Compute the average velocity V2 assuming radial flow in mm/sec D-80 mm 3 mm 4 mm 4 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Water is flowing through a pipe of 5 cm diameter under a pressure of 29.43 N/cm² (gauge) and with…

Q: : If flow rate in pipe shown is (0.5m'/s) find the (H). water D= 300 mm 2)

Q: A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see…

A: Fluid relative density = 0.88 PA = 150 KPa PB = 225 KPa ZA = 9.8 m ZB = 0 m

Q: V Thing Pipe area = 0.10 m2 Water flows at a rate of 1.6 m /s from a large tank and passes through a…

A: Given:Q=1.6 m3/sA=0.10 m2z=30 m

Q: Water is to be pumped through 1500 ft of pipe from the lower to upper reservoir at a rate of 4…

Q: 2 Q2 = 10 liter/s %3D 3 DI =? Water D3 = 65mm Tank base area=1 m²

A: In the tank, some pipes are inlets and some are outlets. From inlet the water enters within the tank…

Q: 1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm…

A: Given data Flow rate = 500 gpm Pressure = 35 psi Density = 62 lbm/ft^3 Find the pump head

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

A: Given:The diagram of the problem is given below;The volume flow rate through the larger tube, The…

Q: 2- A pipeline carrying oil (sp. gr = 0.87) changes in diameter from 200 mm at position #1 to 500 mm…

A: Given, SG= 0.87 d1 = 0.2 m d2 = 0.5 m z1 = 0 m z2 = 4 m p1 = 100 KN/m2 = 100000 N/m2 p2 = 60 KN/m2 =…

Q: Consider a desired pump operating condition which adds 35 psi at a flow rate of 500 gpa to water.…

A: Given data Pressure = 35 psi Flow rate = 500 gpm Density of water = 62 lbs/ft^3 Find the pump head…

Q: 4. The pipe system shown in the Figure. The flow rate in pipes AB and FG is 0.88 n'/s. All pipes are…

Q: In Figure below, the pipe entrance is sharp-edged having K1 = 0.5, and for the open globe valve…

A: Given that, K1=0.5K2=6Flow rate of water, Q=0.015 m3/sec,Density of water, ρ=1000 kg/m3Friction…

Q: A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are…

Q: Find the pressure head at entry of the pipe, when the pressure of flowing water is 125 N/cm? The…

A: It is required to determine pressure head at entry of pipe in Pa

Q: / A fluid containing (water, oil, air) flowing through the tube and open to the atmosphere as shown…

A: Given data

Q: Elevation = ? reservoir on the right at a rate of 0.45 m/s. The formula for the head losses in the…

Q: Q2- A (0.14 m'/s) oil has (density 860 kg/m' & viscosity 0.026 pa.s) is pumping from first tank to…

Q: Fluid is flowing in a sudden expanding pipe as shown in figure. The co-efficient of expansion loss…

Q: Water is to be pumped through 1500 ft of pipe from the lower to upper reservoir at a rate of 4…

A: Given:Length of pipe, L=1500 ft =457.2 mVolume flow rate, Q=4 ft3/s =0.113267 m3/sdiameter, d=8 in…

Q: Q3/ The pipe has a different diameter: diameter (Di = 4 m) changes into (Dz = 6 m). The water…

Q: Q.4. In the system shown in figure, the water flow rate ,Q= 0.5 m3/s and pressure P=20 kPa are…

A: In a steady flow system, the mass flow rate entering the system is equal to the mass flow rate…

Q: For the moving cart and vane in the figure below, let the jet be water of 3 in diameter at 35 ft/s.…

Q: eter 20mm and vertical int 'B') water is flow t a is 0.008. Pressure hea

Q: The pump in the figure shown draws water from a reservõir and discharge through a which terminates…

Q: 6) Through the pipeline system in the figure, calculate the flow velocity and flow rate at B, if Pa…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: For the system shown in the figure, calculate (a) the volumetric flow of water out of the nozzle…

Q: 7. A siphon draws oil (sg=0.86) as shown in the figure. Determine the volume flow rate of oil from…

A: Consider 1 is the section in the siphon at the level of oil in the tank, and 2 is the section at…

Q: Q3/ The pipe has a different diameter: diameter (D1 = 4 m) changes into (D2= 6 m). The water…

Q: :-in the figure shown find the pump power if the discharge of oil is 200L/sec and the relative…

Q: Kerosene (SG = 0.82) is flowing through a piping system as shown in Figure 3. The diameter pipe of B…

A: Given; The diameter of pipe B and D, dB or D = 90 mm The diameter of pipe C, dC = 130 mm The…

Q: Dots Reset All Prespure .4 m 110.992 kPa 3.5 m Prespure 116.285 kPa Flow Rate: 4250 0 LIS Area 08 m…

Q: A pump delivers water from a tank (A)X water surface elevation=D110m) to tank B (water surface…

Q: Problem 4. (30') Water flows steadily through the reducing elbow shown below. The elbow is smooth…

Q: The sprinkler system is used for watering the garden as given figure below. Working fluid enters the…

Q: In the pipeline in the figure, water is transmitted from a-tank to Bdepo with a flow rate of 400L/s…

A: Water flow rate, Q=400 L/s=0.4 m3/s Pipe lengths, L1=20 m, L2=30 m Pipe diameters, D1=0.2m, D2=0.4 m…

Q: A fluid is pumped at a rate of 0.00156 m³/s through a 0.025-m-diameter pipe to fill a water tank as…

Q: P₁ = 80 kPa PB = 50 kPa Calculate the friction head loss for a water Q-1 flowing from point A to B.

Q: Water is pumped at a rate of 21.4 m/s from tank (A) and out through a 300.5 m pipe to tank (B). The…

A: Given details: Q= 21.4 m3 L= 300.5 m H= 70 m f= 0.02 Note: Inbuilt math type is not proper work so…

Q: 2. A turbine is used to produce 2700 hp by expanding the water between points 1 and 2. Water flow…

Q: I need help with this question: Q. A sprinkler system pumps water through a large pipe inlet with…

A: To find: (a) The expression for the velocity of water leaving the sprinkler. (b) The expression for…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

5. Kerosene (sp.gr. = 0.88 ) enters the cylindrical arrangement as shown on the figure at
section 1 at 0.08 N/s. The 80 mm diameter plates are 3 mm apart. Assuming steady flow
and unit weight of water is 9790 N/m3
(a) Compute the inlet average velocity Vị
(b) Compute the outlet volume flux in m/sec
(c) Compute the average velocity V2 assuming radial flow in mm,
m/sec
D=80 mm
3 mm
4 mm
4 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 12 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

m². -5 S Figure shows a portion of a fire protection system in which a pump draws water at 60°F (v =1.21 ×10¯ from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height h of the water level in the tank in order to maintain 5.0 Psig pressure at point A h 25 ft A Pump 2600-ft-long 8-in Schedule 40 steel pipe Flow Flow 45-ft-long 10-in Schedule 40 steel pipe B
What is the pressure in the inlet? (Note: You cannot relate directly what is in the inlet section towards the exit/exhaust section, but: Inlet to Throat to Exit Section)
5. Calculate the power delivered by the oil to the fluid motor shown in the following figure if the volume flow rate is 0.25 m3/s. There is an energy loss of 1.4 N.m/N in the piping system. If the motor has an efficiency of 75 percent, calculate the power output. ( Oil (sg=0.86) Motor Flow Diameter 15 cm- 10 m
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.
In the hydroelectric power plant whose cross-section is given, the flow rate of Q=33.045 m^3/sec is transmitted to the power plant through a D=1.6 meter diameter penstock. Ignoring friction losses; a) Find the internal pipe pressure at point 2 ( at the below ). b) Find the resultant force (F) and its direction (O) that the water exerts on the fixation mass. c) Calculate the electrical power generated in the plant. (Pwater= 1 ton/m^3, Ywater= 9.81 kN/m^3, g=9.81m/s^2, Beta= 45 degree
Task 3 - Flow through a Diffuser Water flows at 7.2 m/h through the depicted horizontal diffuser which gradually enlarges from a d, = 40 mm to a d, = 50 mm diameter pipe. Mind units and elementary knowledge. EGL (Bernoulli flow) d1 d2 arbitrary reference plane a) Calculate the head loss h = and the resulting frictional pressure drop Ap, of the 28 dissuser.
Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 19 lb/ft^ 3 . What is the mass flow rate? If viscous effects are neglectedTake the specific weight for mercury equal to 846 and for water equal to 62.4 at 68 F
i need the answer quickly
Q4: A 300 L/s of water flow through pipe Shown in figure (4). The pressure at entrance is 70 KPa. Calculate the force by fluid of sp.gr-0.9 on the bend if the volume of bend is 0.085 m³. (R= 8.55 KN) D₁=30cm D₂=20cm 6 Q4 1.5