Q.2. A bolt is subjected to a tensile load of 18 kN and a shear load of 12 kN. The materia has an yield stress of 328.6 MPa. Taking factor of safety as 2.5, determine the core diameter of bol according to the following theories of failure. (1) Rankine's theory, (ii) Shear stress theory, (iii) Shear energy theory and (iv) Saint Venant's theory. Take Possion ratio = 0.298

Q.2. A bolt is subjected to a tensile load of 18 kN and a shear load of 12 kN. The materia has an yield stress of 328.6 MPa. Taking factor of safety as 2.5, determine the core diameter of bol according to the following theories of failure. (1) Rankine's theory, (ii) Shear stress theory, (iii) Shear energy theory and (iv) Saint Venant's theory. Take Possion ratio = 0.298

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Required information The part shown is loaded at point C with 280 N in the positive x direction and…

A: Given:P = 280 N (positive X-axis)Q = 205 N (positive Y-axis)d = 10 mm

Q: Which failure theory would be appropriate to solve the following problem: A rotating shaft is…

A: Given:A rotating shaft is supported by bearings at each end. The shaft supports a single load in the…

Q: A shouldered machine shaft is subjected to bending, as shown. The shaft is made from AISI 1050…

Q: Required information The part shown is loaded at point C with 290 N in the positive x direction and…

A: Given: The load at C, P = 290 N The load at E, Q = 200 N The diameter of the pipe, d = 12 mm

Q: Problem 3: The state of stress at the critical point in a machine component made of cast iron is…

Q: 2. Using maximum shear stress theory (MSS) the factor of safety for ductile material with Sy=220…

Q: MOITAMRORE 10.7 THEORIES OF FAILURE 10-75. The components of plane stess at a critical point on an…

Q: Two cylinders are slip-fitted together to form a composite open cylinder. Both cylinders are made of…

A: Given DataFor Inner cylinderri=50mmro=75mmFor the outer cylinderri=75mmro=150mmσy=480MPa

Q: The aluminum shell is fully bonded to the brass core, and the assembly is unstressed at a…

Q: negligible. Determine the safety factor against yield using Coulomb-Mohr failure theory

A: Calculate the normal bending stress at A.

Q: When a hydraulic cylinder is firmly anchored and pushing on a guided load, the effective length of…

A: Effective length of rod (le)= 2 m =2000 mm Diameter of rod (d)= 3.8 cm= 38 mm yield stress for 304…

Q: Answers provided as well.

A: Step 1: Step 2: Step 3: Step 4:

Q: The body of a DaVinci hospital robot made of steel material The material was statically loaded.…

A: The given values are - σx=80MPa , σy=-40MPa , τxy=50MPaσys=450MPaFOS=Factor of Safety Let us find…

Q: A thick-walled cylindrical pressure vessel with an inside diameter of 280 mm and an outside dianeter…

Q: A bracket is under a loading condition shown below. It's made from a steel with yield strength (Sy)…

A: Write the given information.

Q: An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 356 MPa, and at compression Suc…

Q: An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 345 MPa, and at compression Suc…

A: The ultimate tensile strength (UTS) of a material is the highest stress it can withstand when…

Q: Use the von Mises failure criterion to solve for the minimum required yield stress if a factor of…

A: GIVEN DATA- σX =100MPa σY=-78MPa τXY = 30MPa WE HAVE TO CALCULATE YIELD STRESS ACCORDING TO VON…

Q: A brittle material has the properties Sut = 30kpsi and Suc = 90kpsi. Determine the factor of safety…

Question

Q.2.
A bolt is subjected to a tensile load of 18 kN and a shear load of 12 kN. The materia
has an yield stress of 328.6 MPa. Taking factor of safety as 2.5, determine the core diameter of bol
according to the following theories of failure.
(i) Rankine's theory,
(ii) Shear stress theory,
(iii) Shear
(iv) Saint Venant's theory. Take Possion ratio = 0.298
energy theory and

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A brittle material has the properties . Sut = 30 kpsi and Suc = 90 kpsi Using the brittle Coulomb-Mohr and modified-Mohr theories, determine the factor of safety for the following states of plane stress.
The shaft is supported by journal bearings at A and B that exert force components only in the x and z directions. Part A d= PLÅ Value Ĵ t O Determine the smallest diameter of the shaft. Use the maximum shear stress theory of failure with Tallow Express your answer to three significant figures and include appropriate units. Units HATT F = 200 lb ? X 8 in. 1 4 in. 8 in. N A 8 ksi 4 in. D F. = 50 lb 8 in. 4 in. F = 250 lb 4 in. SE B y
Q1) A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of Syt = 50 kpsi and Sye = 65 kpsi. Using the ductile Coulomb-Mohr theory, determine the factor of safety for the states of plane stress. 0x = 35 kpsi, and oy = 20 kpsi, Txy бу 0 Submit your answer in 4 significant digits. =
Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350 MPa. Using the distortion- energy and maximum-shear-stress theories, determine the factors of safety for the following plane stress states. 0x² =104 MPa, 0y = 19 MPa, and Txy = -19 MPa I The factor of safety from the maximum-shear-stress theory is 3.8 3.45 and the factor of safety from the distortion-energy theory is
Problem 19.1 The shaft shown in the following diagram is supported by two self-aligning bearings at A and B and is subjected to the loads shown on the chain sprockets. 50 mm 100 mm. 100 mm F 30 mm 3000 N 100 mm 50 mm
Two steel plates are held together by two bolts. (/6) a. Determine the required diameter of the bolts if the failure shear stress is 300 MPa using a Factor of Safety (FS) of 2. b. Using the answer from a. above, determine the steel plate thickness if the failure bearing stress of the steel is 350 MPa using FS = 1.5. Show your work. OKN Two Bolts P=60KN
please help
5. A brittle steel bar has the dimensions shown. Determine the maximum axial force P that can be applied not to exceed the allowable tensile stress of allow= 100 MPa. (Make sure to determine and account for the stress concentration factors). K 3.0 2.8 2.6 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0 P 0.1 0.2 0.3 W h W h 30 mm - 4.0 = 3.0 W Jang W h W h II = || 24 mm it P ht 2.0- = 1.5. T AL W W 12 mm 1.2- - 0.4 0.5 0.6 0.7 0.8 0.9 r 1.0 K 60 mm 3.2 3.0 2.8 2.6 2.4 2.2 2.0 0 0.1 r = 15 mm P 0.2 2r avg 0.3 2r P (w – 2r)t 0.4 0.5
Why does the answer of this problem consider radial stress if it is a thin walled?
The principal stresses at a point in a critical section of a machine component are sigma_{1} = 60MPa, sigma_{2} = 5MPa and sigma_{3} = - 40MPa For the material of the component, the tensile yield strength is sigma_{y} = 200 MPa According to the maximum shear stress theory,what is the factor of safety.
Please provide the correct solution asap. Handwritten recommended
The material for the bolt shown in Figure 2, the angled joint has an ultimate tensile strength of 600 MPa and shear strength of 300 MPa. The diameter of the bolt is 10 mm. Determine the factor of safety. Assume force of F = 25 kN. F+ 60% Figure. 2 F