Two cylinders are slip-fitted together to form a composite open cylinder. Both cylinders are made of a brittle material whose stress-strain diagram is linear up to the ultimate strength 480 MPa. The inner cylinder has inner and outer radii of 50 and 75+ mm, respectively. The outer cylinder has inner and outer radii of 75 and 150 mm, respectively. Determine a) the shrink pressure ps and b) maximum internal pressure p, that results in initiation of yield simultaneously at the inner radii of both cylinders. Use the maximum principal stress criterion of failure.

Two cylinders are slip-fitted together to form a composite open cylinder. Both cylinders are made of a brittle material whose stress-strain diagram is linear up to the ultimate strength 480 MPa. The inner cylinder has inner and outer radii of 50 and 75+ mm, respectively. The outer cylinder has inner and outer radii of 75 and 150 mm, respectively. Determine a) the shrink pressure ps and b) maximum internal pressure p, that results in initiation of yield simultaneously at the inner radii of both cylinders. Use the maximum principal stress criterion of failure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pressure vessel is exposed to a combination of loads as shown below. The vessel (diameter 100 mm) has a wall thickness of 3 mm. Address the following: (a) If the yield strength of the material is 144 MPa, determine the largest tension force P with respect to a factor of safety of 2 applied to the distortional energy theory. (b) If the applied torque and tension load were removed, determine the minimum wall thickness using a factor of safety of 1.75 with respect to the distortional energy theory. Illustrate you results using an appropriate yield envelope. p = 3.5 MPa T = 450 N-m show all wah P
The steel bar with a circular cross section of 14 mm diameter and 22 cm length, produced from a material with linear elastic behavior, elongates 0.11 mm under the effect of 16 kN tensile load and breaks at 24 kN load. How many MPa is the modulus of resilience of this bar?
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14 mm, and the rod length was 440 mm. When the applied torque reached 225.3 N-m, a shear strain of 2105 microradians was measured in the specimen. What was the angle of twist in the specimen? Calculate the shear stress in the specimen. Answer: T = MPa
A metal rod is 50 mm in diameter and 1.3 m long. The rod has a collar on one end and is suspended vertically. The height through which this load may fall if the instantaneous stress is limited to 90 MPa is 1.71870x 10-3 m. The value of Young modulus is 132.40 GPa. 2.1 Calculate an extension when a weight of 30 kN is suddenly lowered onto the collar. 2.2 Calculate the force required to cause the maximum stress.
The stresses on the surface of a hard bronze component are shown in the figure below. The yield strength of the bronze is σY = 345 MPa.a) What is the factor of safety predicted by the maximum-shear-stress theory of failure for the stress state shown? Does the component fail according to this theory?b) What is the value of the Mises equivalent stress for the given state of plane stress?c) What is the factor of safety predicted by the failure criterion of the maximum-distortion energy theory of failure? Does the component fail according to this theory?
For a given homogeneous, isotropic, linearly elastic material, E = 15e6 psi and v = 0.3. Solve for the shear modulus. 2.1.1 Homogeneous, isotropic, linearly elastic materials For specimens undergoing small deformations, the stress-strain diagram often ex- hibits a linear behavior. Although this is a very crude approximation to the behavior of actual materials, it is a convenient assumption that is often used for preliminary evaluation. A linear relationship between stress and strain can be expressed as 01 = E €1, (2.1) where the coefficient of proportionality, E, is called Young's modulus or modulus of elasticity. Since strains are non-dimensional quantities, this coefficient has the same units as stress quantities, i.e., Pa. This linear relationship is known as Hooke's law. The elongation of a bar in the direction of the applied stress is accompanied by a lateral contraction that is also proportional to the applied stress. The resulting defor- mations for this uniaxial state of stress…
(30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14 mm, and the rod length was 440 mm. When the applied torque reached 225.3 N-m, a shear strain of 2105 microradians was measured in the specimen. What was the angle of twist in the specimen? Calculate the shear stress in the specimen. Answer: T= 418.16 Use Hooke's Law to calculate the shear modulus of the specimen. answer: MPa G = i MPa
EXAMPLE 3.9 Finite-element²¹ analysis shows that a long structural component car- ries a uniform axial stress of 35 MPa (T) (Figure 3.29). A hole in the center needs to be drilled for passing cables through the structural component. The yield stress of the material is 200 MPa. If failure due to yielding is to be avoided, determine the maximum diameter of the hole that can be drilled using a factor of safety of 1.6. 10 mm H = 100 mm -d- Figure 3.29 Component geometry in Example 3.9.
Help me understand by teaching me the solution. Thanks i upvote.