Use the von Mises failure criterion to solve for the minimum required yield stress if a factor of safety of 2 is needed and the applied state of plane stress is as given below. Give your answer as an integer in units of MPa (e.g. 200 or 200MPA) +100MP. %3D Oy = -78M Pa Tzy = +30M Pa %3D

Q: The beam is subjected to the load at its end. Take P= 3.9 kN and V = 2.3 kN. (Figure 1) Part A…

A: Given data: P =3.9 kN V= 2.3 kN Need to determine the maximum principal stress at point B.

Q: Suppose a ball bearing under a given load F1 has a life of L1 = 334 kcycles. Further suppose that…

A:

Q: 1. Determine the diameter size of rods AB, BC and C if ay = 3600 MPa and the safety factor SF= 2.…

A: Determine the diameter size of rods AB, BC and CA, if Yield stress = Sy = 3600 MPa and the safety…

Q: A bar is supported with a pin support as shown. Determine the maximum force, F, that could be…

A: Step 1:  Step 2:Step 3:Step 4: Step 5:

Q: 1. A cold-drawn AISI 1015 steel tube is 300 mm OD by 200 mm ID and is to be subjected to an external…

A: Given data - Outer diameter - 300 mm Internal diameter - 200 mm Yield strength = 600 Mpa It is asked…

Q: The wire-mass system shown is constructed using 6061-T6 aluminum wire. Determine the minimum…

A:

Q: Determine the smallest yield stress for steel that might be selected for the part, based on the…

A: Given data,the state of stressFind outthe smallest yield stress for steel using the maximum shear…

Q: A steel plate is subjected to a constant amplitude uniaxial fatigue loads to produce stresses, max…

A: Assumptions: For through thickness edge crack, α = 1.12, and for ferritic-pearlitic steels, A =…

Q: 8. Refer to the figure below. Even though the cyclic loading accidentally caused the stresses to…

A:

Q: Name. Find the stresses on the 20 degree plane shown. Dřaw and label the Mohr's circle. Fill in the…

A: given; stress in x direction(σx)=-10MPa (compressive)stress in y direction(σy)=8MPa (tensile)shear…

Q: Q 2: A circular rod of 15 mm diameter and 120 mm length, is subjected to 2.5 KN tensile load if the…

A:

Q: 1) The section of the pipe at A is under combined loading due to a tensile force P=70 kips and a…

A: Given data:- Tensile force P=70 kips a torque T=6 kip-ft. Outside diameter = 4.0 in.  Inside…

Q: Determine the smallest diameter of the shaft. Use the maximum shear stress theory of failure with…

A:

Q: End condition total coils wire dia spring index material G squared & ground 14 2.2 mm 10 Hard-drawn…

A: free length l=65mmtotal number of turns nt=14wire diameter  d=2.2mmspring index  c=10G=80GPa=80 x…

Q: A cylindrical steel bar 8 mm in diameter is loaded 1000 cycles per day with a load of 15560 N. How…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.