he principal stresses at a point in a critical section of a machine component are sigma_{1} = 60MPa, sigma_{2} = 5MPa and sigma_{3} = - 40MPa For the material of the component, the tensile yield strength is sigma_{y} = 200 MPa According to the maximum shear stress theory,what is the factor of safety.

he principal stresses at a point in a critical section of a machine component are sigma_{1} = 60MPa, sigma_{2} = 5MPa and sigma_{3} = - 40MPa For the material of the component, the tensile yield strength is sigma_{y} = 200 MPa According to the maximum shear stress theory,what is the factor of safety.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the yield strength of a material required such that the component would not fail when subject to the following stresses sigma1 = 2 MPa and sigma 2= -15 MPa sigma 3 = 10 MPa). Use a yield criterion that assumes that yield failure will occur when the maximum shear stress in the complex system becomes equal to the limiting shear strength in a simple tensile test.
At a point in a steel structure (Y = 490 MPa, E = 200 GPa, v = 0.29), the principal stresses are o1 = 122 MPa, o2 = 0 MPa and o3 = -63 MPa. What is the factor of safety against yielding using maximum distortion energy von Mises) criterion?
suppose the free length is 65 mm. Find the stress at solidity in units of MPa Circle final answer
Assume: Yield strength = 100ksi
Introduction to Fem
b) A hollow tube of cross-section as shown in Figure 2.2 is subjected to an axial tensile force of 100kN. If the tensile yield stress of the material is 280MN/m², use the von Mises yield criterion to determine if a torque of 6kNm can be applied without causing the tube to yield. * -50 mm 45 mm Figure 2.2: Hollow tube profile
2
URGENT
The stresses on the surface of a hard bronze component are shown in the figure below. The yield strength of the bronze is σY = 345 MPa.a) What is the factor of safety predicted by the maximum-shear-stress theory of failure for the stress state shown? Does the component fail according to this theory?b) What is the value of the Mises equivalent stress for the given state of plane stress?c) What is the factor of safety predicted by the failure criterion of the maximum-distortion energy theory of failure? Does the component fail according to this theory?
Q4 Beta =111 Please provide justified answer asap to get a upvote
i li. الامتحان هو سؤالان فقط Q. 1: If a material is cast iron (ultimate tensile strength = 300 Mpa, ultimate compressive strength - 900 Mpa) and the stress state at a point is shown in Fig. 1. Using a graphical method, find safety factor against static failure using 100 Mpa (a) Rankine failure theory (b) Coloumb - Mohr theory (c) Modified Coloumb - Mohr theory 50 Мра إضافة ملف Q.2 For a rotating shaft of diameter 15 mm as shown in Fig. 2. If the material is AISI-1045 CD, Find the safety factor II >
A stainless steel is exposed to a temperature of 800 °C. What is the maximum allowable stress level for a rupture lifetime of 7 years? 103 T(20 + log t,)(°R-h) 25 30 35 40 45 50 |100 100 |10 10 1 12 16 20 24 28 103 T(20 + log t,)(K-h) Stress (MPa) Stress (103 psi)