Q.1. A T-section 150 mm×130 mm×30 mm is used as a strut of 5 m long with hinged at both ends. Calculate the crippling load, if Young's modulus for the material is 200 GPa. Calculate also the crippling load for one end hinged and one end fixed for the same strut, and compare the result of the erippling load for the two types of boundary conditions.

Q.1. A T-section 150 mm×130 mm×30 mm is used as a strut of 5 m long with hinged at both ends. Calculate the crippling load, if Young's modulus for the material is 200 GPa. Calculate also the crippling load for one end hinged and one end fixed for the same strut, and compare the result of the erippling load for the two types of boundary conditions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please answer all with a complete solution thank youu
A metal rod is 50 mm in diameter and 1.3 m long. The rod has a collar on one end and is suspended vertically. The height through which this load may fall if the instantaneous stress is limited to 90 MPa is 1.71870x 10-3 m. The value of Young modulus is 132.40 GPa. 2.1 Calculate an extension when a weight of 30 kN is suddenly lowered onto the collar. 2.2 Calculate the force required to cause the maximum stress.
please help solve and explain
A solid circular rod 200 mm long and 20 mm in diameter has an axial force of P. are exposed. P force and elongation of the rod when this force is applied is below the elasticity of the material, taking as the values given opposite your names in the table presented Calculate the modulus E and the shear modulus G. Take the Poisson's ratio () 0.3. P (N) δ(mm) :500 1,6
4. A steel rod of length L and uniform cross sectional area A is secured between two walls, as shown. Use L=1.7 m, E = 200 GPa, a = 11.9 × 10-6 /°C and AT = 70 °C. Calculate the stress for a temperature increase of AT for: a) The walls are fixed. b) The walls move apart a distance 0.4 mm. (20 pts)
Please help me thanks!
Problem. A load of 98 kg is supported by a wire of length 1.8 m and cross-sectional area 0.12 cm². The wire is stretched by 0.2 cm. Find the stress, strain, and Young's modulus for the wire. Answer: 8x10' N/m2; 0.11x102; 7.2x101º N/m?.
2. The bottom shell of a steel tanker is longitudinally framed. The spacings of transverse floor and longitudinal are 5 m and 0.8 m respectively. The bottom plating is 12 mm thick and the longitudinals are 150 x 10 mm flat bar. For higher- tensile steel, Young's modulus E = 210 kN/mm and yield stress oy = 340 N/mm?. Calculate the Euler buckling stress of the stiffened bottom panel and comment on the result. State any assumptions made. [342 N/mm]
Problem 1: A steel rod with a cross-sectional area of 0.20 in´ is stretched between two fixed points. The tensile load at 65°F is 1250 lb. What will be the stress at 0°F? At what temperature will the stress be zero? Assume a = 6.5×10° in / (in.°F) and E = 29 x 10° psi.
A solid steel bar 250 mm long is 10 mm square over part of its length, the remainder being circular with a diameter of 25 mm. A gradually applied tensile load P kN induces maximum stress in the bar of 200 MPa. The total strain energy in the bar when this stress of 200 MPa is acting is 1,3 Joule. Take E = 200 GPa Calculate : The load The length of the square portion of the bar The load that falls from a height of 8 mm and induces 1,3 Joules in the bar
6.10 - This is a statics problem that deals with ‘Zero-Force Members’.
Consider the steel truss and member cross-section presented in figures below. All the members of the truss have the same cross-section as shown in the figure to the right. They all also have a Young's Modulus of 210 GPa. What can the highest value of force F be before member AC fails by buckling? Force 1AN - 300 mm 40° 4 m $35 mm 7m 300 mm 8 m 35 mm 35 mm 35 mm Please provide your answer in kN.