6-10 A solid plug gauge of steel has a diameter of 2.0004 cm and is forced into a ring gauge of the same material, which measures 2 cm inside diameter and 4 cm outside diameter. Its axial length is 2 cm. What is the maximum stress in the ring, and what force is required to slide the plug, assuming the coefficient of friction to be 0-3 ? Take E = 200 GPa.

6-10 A solid plug gauge of steel has a diameter of 2.0004 cm and is forced into a ring gauge of the same material, which measures 2 cm inside diameter and 4 cm outside diameter. Its axial length is 2 cm. What is the maximum stress in the ring, and what force is required to slide the plug, assuming the coefficient of friction to be 0-3 ? Take E = 200 GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two plates of which (2.5 d) and d as outer and inner diameter respectively and thickness 25 mm each are held together by means of a bolt. The bolt material S-400 N/mm² and E210000 N/mm² while plate material E= 72000 N/mm². The initial preload in the bold is 6.0 KN and force on the joint is 12 kN. Find out size of bolt assuming factor of safety 2.0.
Asap
The following figure shows the critical position of a crane that supports 2.5 Tons of load by means of a chain. You are delegated the responsibility of building a crane with similar geometric characteristics and load capacity. The diagram of free body of the crane arm can be redrawn as follows. (check the attached image "fbd") Assuming that the crane arm will be made of steel with yield stress sigmaY =220 MPa and that you must consider a safety factor of F.S.=1.5, propose a profile from the following catalog for the manufacture of the crane arm. Ignore the effects of shear forces on this element. On the other hand, it is very important that you consider the effects of axial loads. Commercial profiles for arm construction. (Check image "profiles")
Consider a steel cube with side length L and each of its faces normal to the orthogonal axes x, y, and z as shown below. If the cube is subjected to a constant tensile force T along the x-axis and the faces along the y- and z- axes are left free and unsupported, which of the following best describes what is expected to happen? Z Select one: O A. The cube will expand along the x-axis and compress along the y- and z-axes. B. The cube will expand along the x- and y-axes and will not deform along the z-axis. O C. The cube will expand along the x-axis and will not deform along the y- and z-axes. O D. The cube will compress along the x-axis and expand along the y- and z-axes.
When a bar of 22 mm diameter is subjected to an axial pull of 60 kN the extension on the 49 mm gauge length is 0.1 mm and there is a decrease in diameter of 0.013 mm. Calculate the Young's Modulus. Provide your answer in GN/m2 to the nearest whole number.
A threaded machine bolt of 3/4 in diameter is screwed up tightly, fastening together two steel parts. To avoid the failure of the bolt in shear, the unit shearing stress must not exceed the elastic limit stress of 36000 psi. What maximum pull may safely be exerted on a wrench with a 20 in. moment arm to avoid failure on the root area if its root diameter is 0.6688 in. and if we assume that friction under the bolt head nullifies 25 percent of the pull
A bracket shown in Fig.(2) is fastened to the wall by four bolts equispaced on a (10 cm) diameter bolt circle. The bracket is subjected to a fluctuating force (0-50 N) . Find the forces acting on each bolt and then choose a suitable bolt size and a preload that will give minimum safety factor (1.5) for any mode of failure.
STATICS OF RIGID BODIES RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES.