Problem 8 The shear stress-strain diagram for an alloy is shown in the figure. If a bolt having a diameter of 0.25 in. is made of this material and used in the lap joint, determine the modulus of elasticity E and the force P required to cause the material to yield. Take v = 0.3. P 7 (ksi) T Ty=50 0.004 y (rad)

Problem 8 The shear stress-strain diagram for an alloy is shown in the figure. If a bolt having a diameter of 0.25 in. is made of this material and used in the lap joint, determine the modulus of elasticity E and the force P required to cause the material to yield. Take v = 0.3. P 7 (ksi) T Ty=50 0.004 y (rad)

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 40P: The uniform boom shown below weighs 3000N . It is supported by the horizontal guy wire and by the...

See similar textbooks

Similar questions

Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
One end of a vertical metallic wire of length 2.0m and diameter 1.0mm is attached to a ceiling, and the other end is attached to a 5.0N weight pan, as shown below. The position of the pointer before the pan is 4.000cm . Different weights are then added to the pan area, and the position of the pointer is recorded in the table shown. Plot stess versus strain for this wire, then the use the resulting curve to determine Young’s modulus and the proportionality limit of the metal. What metal is this most likely to be?
The bulk modulus of a material is 1.01011N/m2 . What fractional change in volume does a piece of this material undergo when it is subjected to a bulk stress increase of 107N/m2 ? Assume that the force is applied uniformly over the surface.
A thin rectangular plate is uniformly, deformed, as shown. Determine the shear strain y, at P. Assume a - 21 in, b- 29 in, c- 0.16 in, and d- 0.28 in. R Answer:Y prad.
The beam is supported by a pin at A and a short link BC. Figure 1 of 1 > 0.5 m Tadika 1m 1.5 m 1.5 m H. Part A If P = 13 kN, determine the average shear stress developed in the pins at A, B, and C. All pins are in double shear as shown, and each has a diameter of 17 mm. (Figure 1) Enter your answers separated by commas. TA. TB. TC = Submit Provide Feedback 197| ΑΣΦ | 11 | vec Request Answer MPa I
How do I determine the maximum magnitude P?
A force is applied to a circular surface with area 70 cm2. The surface is parallel to the x-y plane. Fx = 12N, Fy= 16N, Fz= 20N (see figure below). What magnitude of the total shear stress in Pa? Give your answer to 2 decimal place. Z j F auto par possible partical credits. Symbols can be found by clicking the button.
The rubber blocks shown are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 336 N causes the upper frame to be deflected downward by 5.5 mm. Determine the shear modulus Gof the rubber blocks. Assume a = 10 mm, b = 22 mm, and c = 27 mm. Double U anti-vibration shear mount b P Rubber block dimensions Shear deformation of blocks Answer: Shear Modulus G = i MPa.
Current Attempt in Progress A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain y, at P. Assume a - 1020 mm, b - 700 mm,c-1 mm, and d- 0.6 mm. R Answer: Shear strain yey = prad.
Problem 8 For the given beam draw the diagrams of shear force and bending moment, and determine the maximum normal stress due to bending. 800 lb/in. 1 in. A 20 in.- B 8 in. T C 3 in. H 2½ in.
written solution