Problem-5 A compression spring is made of a music wire of 2 mm diameter having a shear strength and shear modulus of 800 MPa and 80 GPa respectively. The mean coil diameter is 20 mm, the free length is 40 mm and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately...

Problem-5 A compression spring is made of a music wire of 2 mm diameter having a shear strength and shear modulus of 800 MPa and 80 GPa respectively. The mean coil diameter is 20 mm, the free length is 40 mm and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately...

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in bronze bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 144.21 102.49 341.33 54.56
A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid A36 steel with a 20 mm diameter (E = 200 GPa). Outer sections DA and BC are solid red brass (E = 101 GPa) with a 50 mm diameter. A previous analysis by a now departed coworker correctly determined that the internal normal stress in DA was 54.952 MPa compression. You are asked to determine the horizontal displacements of joints A and B.
Determine the tensile strain Original length L = 500 mm Tensile deformation = 2.5 mm
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 13 mm and an elastic modulus of E = 70 GPa. The steel rod has a diameter of 20 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.9 m, and c = 1.2 m. What is the magnitude of load P that is necessary to displace point A 14 mm to the left? a b (1) P Answer: P = i (3) B KN O
answer this please asap. this 30 mins left in the tank
solve correctly and show the complete solution.
= Problem #2: A steel bolt with a diameter of 8 mm fits through an aluminum sleeve with and outer diameter do 13 mm and an inner diameter d; = 10 mm. The apparatus is snug-fit and stress-free at an initial temperature of 20° C. If the apparatus is slowly heated to 110° C, find the axial stress in the bolt and the sleeve, and state whether each is in tension or compression. You may ignore the thickness of the washers at either end of the sleeve. Aluminum Young's Modulus (GPa) 70 Coeff. Thermal Exp. (/°C) | 23×10-6 Steel 200 14x10-6
In figure shown below B 960 Imm 640 N 3 280 mm 960 N a. Determine the tension in segment AC b. Determine the tensibn in segment BC
Show complete and neat solution
Asap
The rigid beam is supported by a pin at B and wires AD and CE. (Figure 1) The load P on the beam causes the end A to be displaced 7.5 mm downward. The wires are unstretched when the beam is in horizontal position. Figure 3 m 2 m -2 m 1.5 m E 1 of 1 2 m ▼ Part A Determine the normal strain developed in wire CE. Express your answer in millimeters per millimeter to three significant figures. ECE = Submit Part B E AD = Submit D Provide Feedback AEO Ivec Request Answer Determine the normal strain developed in wire AD. Express your answer in millimeters per millimeter to three significant figures. AE Ivec S ? Request Answer mm/mm ? mm/mm
The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the figure. 6mm thick steelThe tank is manufactured by joining the plate with a helical weld at an angle of 30°. parallel to the weld seamSince the safe shear stress in the direction is 30 MPa, the maximum pressure that can be used in the tank is determined.calculate.