Problem 4. For the circuit below, find the following total values:(a) Complex and apparent powers absorbed by the loads (i.e. impedances).(b) Average (or real) power absorbed by the loads.(c) Reactive power absorbed by the loads.(d) Power factor seen by the source.(120210°) Vrms (±(302-40°)☐(50/15°)

The total impedance is found from the parallel combination Zeq=(Z11+Z21)−1Given…

Answered: Problem 4. For the circuit below, find…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in Figure Q2. The AC source, Vs, supplies 415220° V with frequency 50 Hz. Based on this information: 5Ω 100 mH 15 Q Load 1 Load 2 i) Calculate the total load impedance. Vs ii) Calculate the current, I. Figure Q2. (ii) Write the waveform expressions in frequency domain for Vs and I. Draw a phasor diagram consists of Vs and I and state the relationship between Vs and I. Determine the power factor and calculate the real power, reactive power and apparent power. Establish the power triangle for the load. (iv)
Fill in the table for a correctly wired duplex outlet (U.S. National Electric Code standards for voltage PARAMETER EQUATION and frequency). Note the used of double- subscript notation. You can assume a 0° phase reference for Vba(t). Vba(t) Vea(t) Vbe(t) Vba (Peak Phasor) Vea (Peak Phasor) Vbc (Peak Phasor) Vba (RMS Phasor) Vea (RMS Phasor) Vbc (RMS Phasor) A C
1. Write down a formula for the three-phase power factor, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula that relates three-phase apparent power to active and reactive power. 3. Draw a graph that depict single-phase waveforms for a purely sinusoidal 50 Hz voltage and a lagging current.
Q.1) A single phase load consisting of 5 2 in series with an inductance of 0.02297 H is operated in a phase control mode with a of 90°. The source is 240 V RMS, 60HZ. Find: a) Draw the waveform of VTI and VR. b) Find the conduction angle (6). c) Calculate the RMS value of load current. d) Find the power factor e) What is the minimum value of a for which phase control is in effet. f) Find the size of the first three terms in the Fourier series for the current. T Zoom
A synchronous generator has been synchronized to an infinite grid of 13.8 kV and 60 Hz. The generator prime mover C/C is such that the no-load frequency is 62.5 Hz and the power slope is 1 MW/Hz. The AVR C/C (The reactive power against the terminal voltage C/C) is such that the zero reactive power voltage is 14.6 kV, while the slope is 0.4 MVAR/kV. Calculate (a) the kVA loading of the generator and its power factor. (b) the settings of the prime mover and AVR such that the generator delivers 3 MW at 0.85 lagging power factor.
i = i, 太Ts Load Highly inductive load Vo Figure 5 c) Figure 6 is the waveform of output voltage, changer. The primary voltage is 220 V (rms), 60 Hz. The secondary voltages are V1 = 120 V and V2 = 100 V. If the load resistance is R = 6 Q and the rms load voltage is 150 V with delay angle, a = 93°, determine the; from synchronous connection i. rms current of thyristors T1 and T2. ii. rms current of thyristors T3 and T4. iii. input PF. Vo V2(V; + V2) T T2 Figure 6
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
Please help with the solution.
can you doing this with detail explaination..thank you!

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning