**Problem 3.7 Determination of the modulus of subgrade reaction, k,A plate bearing test was performed on a 45-cm diameter plate. A seatingload of 0.7 daN/cm2 was applied initially after which the load was loweredto 0.1 daN/cm². The strain gages read 55, 103 and 72 hundreds of a mm.The load was then increased to 0.7 daN/cm2 and the gages read 70, 118 and86 hundreds of mm. Determine the reaction modulus k, for a plate diameterof 75 cm.

Answered: Image /qna-images/answer/02d11341-0dd3-4477-b179-acc6a3d77151.jpg

Problem 3.7 Determination of the modulus of subgrade reaction, k, A plate bearing test was performed on a 45-cm diameter plate. A seating load of 0.7 daN/cm² was applied initially after which the load was lowered to 0.1 daN/cm2. The strain gages read 55, 103 and 72 hundreds of a mm. The load was then increased to 0.7 daN/cm2 and the gages read 70, 118 and 86 hundreds of mm. Determine the reaction modulus k, for a plate diameter of 75 cm.

Problem 3.7 Determination of the modulus of subgrade reaction, k, A plate bearing test was performed on a 45-cm diameter plate. A seating load of 0.7 daN/cm² was applied initially after which the load was lowered to 0.1 daN/cm2. The strain gages read 55, 103 and 72 hundreds of a mm. The load was then increased to 0.7 daN/cm2 and the gages read 70, 118 and 86 hundreds of mm. Determine the reaction modulus k, for a plate diameter of 75 cm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The piece of wood shown below was used in an experiment. During the test it sheared parallel to the wood grain along the dashed line. Determine the average shear stress on that failure plane for a maximum load of P = 1000 lb. The dimensions of the wooden specimen are t = 2.0 in. and L = 4 in. P Answer: L Average shear stress = i P t psi
What are the advantages of the stress-strain diagram over a load elongation diagram for showing the results of the test? Significance of the test results.
Part A Determine average normal stress. (Figure 1) Express your answer with the appropriate units. Javg = Part B μA Submit Request Answer Value σ1,02= 20 MPa IVD ΑΣΦ11 Units vec ww Determine the principal stress. Enter your answers numerically separated by a comma. ? 80 MPa 30 MPa www MPa
The piece of wood shown below was used in an experiment. During the test it sheared parallel to the wood grain along the dashed line. Determine the average shear stress on that failure plane for a maximum load of P = 1575 lb. The dimensions of the wooden specimen are t = 2.0 in. and L = 6 in. Answer: L Average shear stress = psi
What are the advantages of the stress-strain diagram over a load elongation diagram for showing the results of the test? Significance of the test results.
The piece of wood shown below was used in an experiment. During the test it sheared parallel to the wood grain along the dashed line. Determine the average shear stress on that failure plane for a maximum load of P = 1575 lb. The dimensions of the wooden specimen are t = 2.5 in. and L = 5 in.
The rectangular plate is deformed into the shape shown by the dashed lines. Suppose that a = 280 mm and b = 420 mm. (Figure 1) Part A Determine the average normal strain along diagonal BD Express your answer using three significant figures. vec Figure (Eavg) BD = mm/mm Submit Request Answer 6 mm 2 mm 2 mm 16 mm Part B D C Determine the average shear strain Yzy at corner B relative to the x, y axes.. Express your answer to three significant figures and include the appropriate units. 2 mm HA B -3 mm (yB)zy = Value Units
Question 3 The strain rosette shown below was used to obtain normal strain data at a point on the free surface of a machine part. Under load, the following strains were measured: Ea = -360 µE, Eb = −230 µɛ, &c = 815 µƐ and v= 0.15 a) Determine the strain components Ex, Ey and Yxy at the point. b) Determine the principal strains and the maximum in-plane shear strain at the point. Figure 1 b 120° 120° 120° a I
The nominal stress-strain diagram for a specimen having an original diameter of 10 mm and a gauge length of 50 mm is shown below. Using the given nominal stress-nominal strain diagram, answer this question. The inset shows a detailed view of the curve at low strains. 400 350 300 250 Stress (MPa) 200 150 100 50 0 0.00 Stress (MPa) 350 kN 300 250 200 150 100 50 0 0.000 0.002 0.004 0.006 0.008 0.010 0.012 Strain 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 Strain 0.18 What is the maximum force that could be applied to the specimen before it plastically deforms?
The tensile test has been performed on a 50 mm long steel tube having 18 mm external diameter and 12 mm internal diameter. The axial load of 2 kN produced a stretch of 3.36 x 10-³ mm and a lateral contraction of the outer diameter of 3.62 x 104 mm. Calculate Young's modulus, Poisson's ratio and bulk modulus for the material
The tube is subjected to a torque of 749 N-m Figure 62°5 6 mm 100 mm 4 mm 4 mm 60 mm B 6 mm 1 of 1
Q1- A concrete cylindrical sample 14.8 cm in diameter and 30.5 cm long is subjected to compression. The sample failed under a compressive load of 698.4 kN and the stress-strain relation showed a complete elastic behavior. If the deformation at 60% of the strength is 0.21 mm, determine the: i- Strain at failure in percent. ii- Young's Modulus of Elasticity in GPa. iii-Length of the sample at half strength in mm. iv- Strain at three quarters of the strength in percent.