The piece of wood shown below was used in an experiment. During the test it sheared parallel to the wood grain along the dashed line. Determine the average shear stress on that failure plane for a maximum load of P = 1250 lb. The dimensions of the wooden specimen are t = 1.5 in. and L = 6 in. P Answer: Average shear stress = psi

The piece of wood shown below was used in an experiment. During the test it sheared parallel to the wood grain along the dashed line. Determine the average shear stress on that failure plane for a maximum load of P = 1250 lb. The dimensions of the wooden specimen are t = 1.5 in. and L = 6 in. P Answer: Average shear stress = psi

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

please be clear
A cylindrical brass specimen having a diameter of 1.10 cm and initial gage length of 4.04 cm is subjected to tensile strength test. The load-deformation values are given in the below table. The final length and final diameter of the specimen were measured as 4.33 cm and 0.92 cm, respectively. Complete the below table and plot true stress-true strain diagram and determine. Yield strength at 0.2 % off-set method. Poisson’s ratio of the material at 135 kN load (assume that there is no volume change) If the material were unloaded from 175 kN, what would be its final length? 1 nm=1*10-9 m, 1 0A=10-10 m
A Brinell test is performed on a steel using a 1.31 in. diameter indenter with a load of 67275 lbs. A 0.75 in. Determine in indentation was measured on the surface of the steel. Determine: a) HBN (psi); b) tensile strength (psi)
NO 1 Please solve and answer correctly, give the complete solutions.
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
Procedure: 1. Measure the dimensions of the specimen and the record them in the date sheet 2. Turn the specimen on its side with respect to its position as molded and center in on life support blocks. 3. Center the loading system in relation to the applied force. 4. Bring the load applying-block in contact with the surface of the specimen at the center and apply a load between 3 and 6% of the estimated load. 5. Grind cap, or use leather shims on the specimen contact surface to eliminate any gap in excess of 0.004 inch (0.10 mm). Gaps in excess of 0.15 inch (0.38 mm) shall be eliminated by capping or grinding. 6. Apply the load on the specimen continuously and without shock. The load shall be applied at the constant rate to the breaking. Apply the load at such a rate that constantly increases the extreme fiber stresses between 125 and 175 psi/min. (0.86 and 1.21 MPa/min) when calculated until rupture occurs. 7. Take three measurements across each dimension (one at each edge and at the…
Read the question carefully and give me right solution according to the question. Don't copy from other websites solution
Example graph of a testing of Reinforcing Steel Bar how can you explain this?
Two 150 mm * 300 mm concrete cylinders with randomly oriented steelfiber contents of 0 and 2% by weight, respectively. After curing for 28 days,the specimens were subjected to increments of compressive loads until failure. The load versus deformation results were as shown in Table P7.45. Assuming that the gauge length is the whole specimen height, determine the following:a. The compressive stresses and strains for each specimen at each loadincrement.b. Plot stresses versus strains for the two specimens on one graph.c. The initial modulus of elasticity for each specimen.d. The ultimate strength for each specimen.e. The strain at failure for each specimen.f. Toughness. Curves may be approximated with a series of straight lines.g. Comment on the effect of adding fiber on the following:i. Modulus of elasticityii. Ultimate strengthiii. Ductilityiv. Toughness
The breaking strength of a 15.0 mm diameter bar was 540 MPa and the cross-sectional diameter after rupture was measured as 12.3 mm. Calculate the ductility in percent shrinkage and the actual stress at break.
The composite bar consists of a 25-mm-diameter A-36 steel segment AB and 60-mm-diameter red brass C83400 end segments DA and CB. (Figure 1) Figure -250 mm- D A 500 mm 75 kN 75 kN 100 KN 100 KN B 1 of 1 > 250 mm- C Part A Determine the average normal stress in segment DA due to the applied load. Express your answer to three significant figures and include the appropriate units. ODA = Submit Part B JAB = O Submit HÅ Value Request Answer Determine the average normal stress in segment AB due to the applied load. Express your answer to three significant figures and include the appropriate units. μA Value C Request Answer Units ? Units ?
I. Problem Solving: Answer what is being required. Show you complete solution. 1. Compression test was applied to a certain type of wood. Compute the stress based on the following dimensions. The grains are parallel with the length. а. Dimension (mm) Load (N) Compressive stress (МРa) Compression Test L = 50 Parallel to the grain B = 75 130,000 W = 75 L = 50 Perpendicular to the B= 75 W = 75 35,000 Grain b. What would be the shear stress for a single shear for the same data in a.? c. What is the modulus of rupture if the width of the specimen is 50mm, depth is