Please complete the following with full workings. :) Question 66 of 10A tension test was performed on a steel specimen havingan original diameter of 12.5 mm and gauge length of50 mm. The data is listed in the table below. (Figure 1)Part ADetermine approximately the modulus of elasticity.Express your answer to two significant figures and include the appropriate units.?E =ValueUnitsFigure1 of 1 >SubmitRequest AnswerLoad (kN) Elongation (mm)Part B0.01250.03750.06250.08750.1257.021.036.050.053.053.054.075.090.097.087.883.3Determine approximately the yield stress.Express your answer to two significant figures and include the appropriate units.0.20.51.02.57.010.011.5?oy =ValueUnitsCubmitDegueet Anour Question 66 ofPart CA tension test was performed on a steel specimen havingan original diameter of 12.5 mm and gauge length of50 mm. The data is listed in the table below. (Figure 1)Determine approximately the ultimate stress.Express your answer to two significant figures and include the appropriate units.HA?ValueUnitsOy =Figure< 1 of 1 >SubmitRequest AnswerLoad (kN) Elongation (mm)Part D0.01250.03750.06250.08750.1250.20.51.02.57.010.011.57.021.036.050.0Determine approximately the rupture stress.Express your answer to two significant figures and include the appropriate units.53.053.054.075.090.0HÀ?97.087.883.3OR =ValueUnitsSuhmitRequest Answer

Given data, Diameter d = 12.5 mm Length l = 50 mm Area of specimen = 122.7 mm2 1. Modulus of…

Question 6 6 of A tension test was performed on a steel specimen having an original diameter of 12.5 mm and gauge length of 50 mm. The data is listed in the table below. (Figure 1) Part A Determine approximately the modulus of elasticity. Express your answer to two significant figures and include the appropriate units. HA ? E = Value Units Figure <) 1 of 1 Submit Request Answer Load (kN) Elongation (mm) Part B 7.0 21.0 36.0 50.0 53.0 53.0 54.0 75.0 90.0 97.0 87.8 83.3 0.0125 0.0375 0.0625 0.0875 0.12 0.2 0.5 1.0 2.5 7.0 10.0 11.5 Determine approximately the yield stress. Express your answer to two significant figures and include the appropriate units. HA ? oy = Value Units

Question 6 6 of A tension test was performed on a steel specimen having an original diameter of 12.5 mm and gauge length of 50 mm. The data is listed in the table below. (Figure 1) Part A Determine approximately the modulus of elasticity. Express your answer to two significant figures and include the appropriate units. HA ? E = Value Units Figure <) 1 of 1 Submit Request Answer Load (kN) Elongation (mm) Part B 7.0 21.0 36.0 50.0 53.0 53.0 54.0 75.0 90.0 97.0 87.8 83.3 0.0125 0.0375 0.0625 0.0875 0.12 0.2 0.5 1.0 2.5 7.0 10.0 11.5 Determine approximately the yield stress. Express your answer to two significant figures and include the appropriate units. HA ? oy = Value Units

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Define the term Underabsorption of Over-Head?
I need the answer as soon as possible
+ X Draw a flow net for the single ro X Bb Collaborate - solu ašluc X HWK #3.pdf X Assignments – 202101_CE333_GA Bb عمادة التعلم الالكتروني والتعليم عن x Bb =S * Ims.kau.edu.sa/bbcswebdav/pid-7525553-dt-content-rid-53158872_1/courses/202101_CE333_GA_15931_EL/HWK%20%233.pdf A TIUDIGMS 8.1 Refer to Figure 8.23. Given: • H, = 6 m Н, %3D 1.5 m Draw a flow net. Calculate the seepage loss per meter length of the sheet pile (at a right angle to the cross section shown). • D = 3 m D, = 6 m Sheet pile H1 k- 4 x 10-4 cm/sec Impermeable layer Figure 8.23 8.2 Draw a flow net for the single row of sheet piles driven into a permeable layer as shown in Figure 8.23. Given: • H = 3 m • H, = 0.5 m Calculate the seepage loss per meter length of the sheet pile (at right angles to the cross section shown). 8.3 Refer to Figure 8.23. Given: • H = 4 m • H, = 1.5 m Calculate the seepage loss in m/day per meter length of the sheet pil (at right angles to the cross section shown). Use Figure 8.12. 8.4 For the…
Please make it fast 104. Wie wird die Kapazität von Parkhäusern berechnet?
orrect response 495.751 MPa 595.095 MPa 278.009 MPa 200.167 MPa < PreviouO
Determine the centroids
From this plan view,which one is the length and which one is the width and please justify your answer
Kindly show me the solution. Thank you.
Glven the technical description of a certain lot, complete the tables below: DIST 40.311 38.910 37.014 51.140 LINE AB BC CD DA Station A B C D * BEARING N 60° 15.3' E S 64° 5.6' E S 42° 29.2' W N 61° 38.1' W interior < division gnerating fr. A Area 1 Area 2 Total Express all values up to 3 decimal places. * If the value is zero just write 0. * If the value is negative, include the negative sign without space in between negative sign and the number. Example: value = - 37, input: -37.000 * For positive values, do not include the + sign in writing the answer. * Do not include the unit in writing the answer/s.
Show the process
Convert 276°25’26” to mils and radians. complete solution pls. thank you
please help me with number 1 :((