If the stress on two perpendicular planes through a point are 80 N/mm2 (Tensile), 30 N/mm2 (Compressive) and 50 N/mm² shear stress then the normal stress on a plane at 50° to that of tensile stress plane will be. N/mm². FAQ Have any Doubt? Correct Option

Q: At a point in an elastic material, ,40 Nimm a direct tensile stress of 80 N/mm and a direct…

A:

Q: Lenght

A:

Q: Which of the following analytical formula you would use to solve for the minimum principal stress: O…

A:

Q: In a stressed member two strain gauges are fixed such that they are inclined at 30° to the known…

A:

Q: total length of column member, I = 3 m beam width, b = 6" or 150 mm (dressed) beam depth, d = 6" or…

A: Total length of column(L)=3 m Total load(P)=56.25 kN Width of column(b)=6" or 150 mm Depth of…

Q: signment #2: Determine Value of x if the Normal stress at rod is equal to rectangular pipe A =400…

A: Let the length be 'L'∑ Fy=0Trod+Tpipe-F=0forTrod=Tpipe2Trod-8=0Trod=Tpipe=4kN

Q: A wire cable was was used to suspend a 500 pound support beam. The orginal length was 12 feet. The…

A: Original length, L=12' Stretched length, L'=12.01' Therefore,  change in length,x=12.01'-12'=0.01'

Q: (c) A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a…

A:

Q: (c) A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a…

A:

Q: Solve it correctly please. I will rate accordingly with 4votes.

A: Given data:- Inner diameter, d= 4 inch Wall thickness, t=0.1 inch Internal pressure, P=50 ksi Axial…

Q: The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both…

A:

Q: The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both…

A:

Q: For a square cross-section bar affected by torsional moment at both ends, the streps components are…

A: σx=150σy=100zxy=-60σmaj/min=σx+σy2±σx-σy22+zxy2               =150+1002±150-10022+602…

Q: An 1130mm? cross sectional area of 50mm long steel bar is subjected to a tensile force of 20 kN and…

A: Given data : Cross sectional area (A)=1130 mm2Force (P)=20 KNElongation (∆L)=0.0435 mmLength (L)=50…

Q: Q. No 1. material. Discuss in detail the Stress Strain Diagram of ductile material and brittle |CLO…

A:

Q: ☐please work out the compliance matrix for the linear isotropic elastic plane stress and plane…

A:

Q: [100 30 For a given stress tensor 30 N/mm? , determine 20 (a) Principal stresses (b) Maximum shear…

A:

Q: A tensile bar has an initial 2.000-in. gauge length and a circular cross-sectional area of 0.2 in.?.…

A: Initial length, li= 2.0 in Initial area, ai= 0.2 in2

Q: At a point on a steel part of landing gear (E = 200 GPa, v = 0.3, Oy = 225 MPa) subjected to a plane…

A: Given Data: 60 degree Strain rosette  εa=1200×10-6εb=-650×10-6εc=550×10-6E=200GPaμ=0.3σy=225 MPa

Q: Part A The stress at a point is shown on the element. Suppose that a = 105 MPa, T,, = 158 MPa .…

A: step 1-

Q: 3. For the state of stress shown below, calculate the principal stresses and maximum shear stress.…

A: Given data  σx = 90 MPa  σy = -60 MPa τxy = 20 MPa

Q: Define the Stress Distribution Under Uniform Strip Load ?

A: Answer A strip loading is known as the load that is transmitted by the finite width and infinite…

Q: The stresses on two perpendicular planes through a point are 50 N/mm² tension, 30 N/mm² compression…

A:

Q: d) What is the maximum in-plane shear stress and the angle of its associated plane? What are the…

A: Given, To determine, d) The maximum In-plane shear stress and the angle of its associated plane and…

Q: The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both…

A:

Q: QUESTION 11 What is the magnitude of the maximum shear stress at the critical location? If none,…

A:

Q: (A) he figure below shows three metal cubes A, B, C of side 100 mm in direct contact, resting on a…

A:

Q: alculate the principal strain.

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A:

Q: rbitrary point, calculate the principal stresses and the бу: 2 = 100 MPa s Txy = 55.9 MPa x=200MPa

A:

Q: min sin gauges are mounted on the surf and gauge C is parallel to the y-a When the part is loaded,…

A:

Q: Why did they convert the compressive stress, fc' in stress distribution, into 0.85fc'? (SD Method)

A: The factor 0.85 you are referring to accounts for long term effects on the compressive strength and…

Q: A 4.5-m-long steel rod must not stretch more than 3.2 mm and the normal stress must not exceed 180…

A: Given data of steel rod  Length = 5 m = 5000 mm  ∆Lmax = 3.2 mm  Normal stress maximum = 180 MPa…

Q: The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both…

A: Given : σx=-160mpaσy=-100mpaτxy=80mpa

Pressure and Stress