Q.12. In a tensile test a test piece of 25 mm diameter, 200 mm gauge length, stretched 0.0975 mm under a pull of 50 kN. In torsion test, the same rod twisted 0.025 radian over a length of 200 mm when torque of 0.4 kNm was applied. Evaluate poisson's ratio and three elastic moduli for the material.

Q.12. In a tensile test a test piece of 25 mm diameter, 200 mm gauge length, stretched 0.0975 mm under a pull of 50 kN. In torsion test, the same rod twisted 0.025 radian over a length of 200 mm when torque of 0.4 kNm was applied. Evaluate poisson's ratio and three elastic moduli for the material.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure.…

Q: Test No Temperature C Deformation rate(mm/min) Strain at break Youngs modulus (Gpa) Stress at…

A: Step 1: UTS mean Ultimate tensile strength. From the conventional stress strain curve, it is…

Q: A UTS with a machine stiffness of 75 KN/mm is used to measure oad/displacement points in the elastic…

A: Given dataDeflection (ΔL) = 0.1 mmInitial length (L) = 102 mmLoad (F) = 2000 NMachine stiffness (k)…

Q: please solve the following problem with paper and pencil and please show the correct answer and step…

A: Given: L = 28 feetE = 29 x 103 ksi The column height at length L= 28 feet. To simplify calculations,…

Q: 1.12 Tensile stress of 500MPA is applied on a steel rod of length 300mm. Determine the elongation in…

A: Given: Original length of rod, l = 300 mm Tensile stress, σ = 500 MPa Modulus of Elasticity, E = 200…

Q: O AF F. p0.2 p0.2 p0.2 S. 0.2-mm (0.2% of 100 mm=0.2-mm)- AL II R.

Q: 30 20kN PVC Wood 20kN 50mm

Q: A strain gauge is attached to the surface of a circular shaft with a radius of 40 mm, as shown in…

A: Given, Radius of circular shaft = 40 mm Strain calculated by strain gauge = -200μ or -200 x 10-6 G…

Q: Answer fast

A: Solution:a) Maximum Stress CalculationFormula:Maximum Stress = Fplastic / A 3. Calculation:Maximum…

Q: A stepped steel shaft shown below is subjected to 10 N-m torque. If the modulus of rigidity is 80…

A: Given: A stepped steel shaft is given,Torque applied, T=10 N-mmodulus of rigidity, G=80 GPa

Q: Can you please answer the following question in the picture and show all of your work in, please.

A: Detailed step by step solution is given below, still if you have any query please feel free to…

Q: Arod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 18…

A: D=18mm L=160mm

Q: Consider a 200 mm dia solid rod having yield stress in shear as 300 N/mm². Calculate the radius of…

Q: At a temperature of 23.1 °C a 0.43-mm gap exists between the ends of the rods shown. At a later time…

A: Determine normal stress in steel rod?

Q: A 0.375 -in. thick rectangular alloy bar is subjected to a tensile load P by pins at A and B. The…

A: Given data in question Load 11 kips Thick 0.375 inch Height 3 inch Strain in longitudinal and…

Q: Q- 7 b, A bar specimen of 36 mm diameter is subjected to a pull of 90 kN during a tension test. The…

A: Given data- A bar specimen- Diameter d=36 mm, Change in diameter ∆d=0.0046 mm, Gauge length L=200…

Q: A hollow cylinder with an OD of 100mm and an ID of 30mm, supports a load of 100kN. What is the…

Q: A sample material with circular cross-section tapers uniformly. Over a gauge length of 200mm, it…

Q: 1.5-7 The data shown in the table were obtained from a tensile test of a metal specimen with a…

Q: A compound bar consists of (4) aluminum alloy bars of (2mm) diameter and (2) steel bars of (3mm)…

A: Thermal Stress : The stress produced by change in temperature in a material is known as thermal…

Q: Q.12. In a tensile test a test piece of 25 mm diameter, 200 mm gauge length, stretched 0.0975 mm…

Q: amplitude was 210 MPa. Compute the maximum and minimum stress. (Enter your answers to three…

Q: Mechanical properties of materials H.W.: The following data where obtained during the tensile test…

A: Mechanical properties are those properties of a material which can be observed under the action of a…

Q: 25 KN III a a ASTEEL ACOPPER STEEL 2.8 m 3.6 m hree vertical rods of equal distance, each has a…

A: Data given:Length of 2 steel rods = 3.6mLength of copper rod = 2.8mDiameter =…

Q: Problem 1.4. A tensile test was conducted on a mild steel bar. The following data was obtained from…

Q: 2.Discuss elastic region in a tensile test and shear test. It is always linear. What is engineering…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

Q: 3. A new material is being developed and tested in the lab. The column was made using the new…

A: To find the elastic modulus and vicose coefficient

Q: The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made…

Q: 4. Sample of steel bar has 50 mm length after performing tension test the final length was 50.2 mm,…

Q: test conducted on a steel bar whose cross section is 0.5 in. by 4 in. is performed. An axial load of…

A: Given:- A=0.5*4 in P=30500lb △L=0.00103in Gauge Length = 2in △d=0.000078in t = 0.5 in To find:- a)…

Q: 1.3 (A). Define the terms shear stress and shear strain, illustrating your answer by means of a…

A: SHEAR STRESS: It is defined as the force, internal resisting force per unit area.The force acting on…

Q: In the tension test of a bar the fractured surface shows a truncated cone, the material may be: Qu O…

A: This question is related to the Strength of Material.

Q: The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made…

Q: A 50 mm X 80 mm rectangular steel plate subjected to the uniaxial stress condition is shown in the…

A: Given data Stress in x direction (σx) = 200 MPa E = 200 GPa μ = 0.3

Q: Problem 1.4. A tensile test was conducted on a mild steel bar. The following data was tained from…

Q: The following force-extension graph is for a cylindrical metal sample with cross section area of…

A: Given data:- The cross-sectional area,A=3.6 mm2 The length,L=240mm

Question

Q.12. In a tensile test a test piece of 25 mm diameter, 200 mm gauge length, stretched
0.0975 mm under a pull of 50 kN. In torsion test, the same rod twisted 0.025 radian
over a length of 200 mm when torque of 0.4 kNm was applied. Evaluate poisson's
ratio and three elastic moduli for the material.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Sketch the stress-strain curve of the following tension test??? In the tension test of a metal fracture occurs at maximum load. The conditions at fracture were: A = 100 mm and L, = 60 mm, the initial values were: A = 150 mm and L. 40 mm.
1.5-6 The data shown in the table were obtained from a tensile test of a metal specimen with a diameter of 0.500 inch and a gage length (the length over which the elongation is measured) of 2.00 inches. The specimen was not loaded to failure. d. Estimate the value of the proportional limit. e. Use the 0.2% offset method to determine the yield strength. Elongation (in.) Load (kips) 872236 DIN 2.5 3.5 5 7 8 9 10 11.5 12 0 0.0010 0.0014 0.0020 0.0024 0.0036 0.0044 0.0050 0.0060 0.0070 0.0080 0.0120 0.0180
#3 solution?
The piece of wood shown below was used in an experiment. During the test it sheared parallel to the wood grain along the dashed line. Determine the average shear stress on that failure plane for a maximum load of P = 1250 lb. The dimensions of the wooden specimen are t = 2.0 in. and L = 5 in.
Asap
Answer in two decimal places please
The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes Ty is 11 N/mm², find the minimum direct stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm?. If the answer is negative do insert the "-" sign. 10 N/mm2 Txy 20 N/mm2 20 N/mm2 Ixy 10 N/mm2
Solid mechanics
Urgent , Handwritten solution. Don't copy paste
Problem 1.4. A tensile test was conducted on a mild steel bar. The following data was obtained from the test : (i) Diameter of the steel bar (ii) Gauge length of the bar (iii) Load at elastic limit (iv) Extension at a load of 150 kN. (v) Maximum load (vi) Total extension (vii) Diameter of the rod at the failure Determine : (a) the Young's modulus, = 3 cm = 20 cm = 250 kN = 0.21 mm = 380 kN = 60 mm - 2.25 cm. (c) the percentage elongation, and (b) the stress at lastic limit, (d) the percentage decrease in area.
I5 In a tensile test experiment of carbon steel. a standard specimen (D= 0.505 in. Gauge length=2.0 in & total length 8 in) had a 0.2% offset yield strength of 80.000 psi and engineering strain of 0.010 at the yield strength point Calculate: The load (force) at this point. The instantaneous area of the specimen at this point. c. The true stress at this point. d. The true strain at this point. e. The total length of the specimen. if the load is released at this point.
Take o,= 120 kPa and o, = 630 kPa Determine the equivalent state of stress on an element at the same point that represents the maximum in-plane shear stress at the point. (Figure 1) Figure K 1 of 1 Oy 400 kPa Part A Find the value of Tmax in-plane- Express your answer to three significant figures and include the appropriate units. µA Tmax in plane = Value Units Submit Request Answer Part B Find the value of oavg Express your answer to three significant figures and include the appropriate units.