A UTS with a machine stiffness of 75 KN/mm is used to measure oad/displacement points in the elastic range of a material. The initial length of the specimen is 102 mm The area of the specimen is 0.00004 m sq The measured deflection and load of a point are: 0.1 mm and 2000 N Estimate the strain on the specimen when loaded

A UTS with a machine stiffness of 75 KN/mm is used to measure oad/displacement points in the elastic range of a material. The initial length of the specimen is 102 mm The area of the specimen is 0.00004 m sq The measured deflection and load of a point are: 0.1 mm and 2000 N Estimate the strain on the specimen when loaded

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel bar of diameter ? = 52 mm is twisted by torques at the ends. The allowable shear stress is 65 MPa. What is the maximum torque that can be applied?
W A 3ft long bar with a 1in x 1in cross section is subjected to a 14,153lb tensile load. What is the tensile stress in ksi? Answer to two decimal places. Type your answer...
Why should the loading be linearly related to the stress or Displacement that is to be determined?
Describe about the cyclic stress ratio?
Problems: Stress (ksi) 53.2 1. Determine the ductility (u) of the material based on the stress- strain diagram (problem S5.1). 43.6 37.1 0.0013 0.0063 0.163 0.247 Strain (in/in)
PROBLEMS 203. During a stress-strain test, the unit deformation at a stress of 5000 psi Wap ODserved to be 0.000167 in./in. and at a stress of 20,000 psi it was 0.000667 in./in. If the proportional limit is 30,000 psi, what is the modulus of elasticity? What is the stress corresponding to a strain of 0.0002 in./in.? Would these re- sults be valid if the proportional limit were 18,000 psi? Explain. E = 30 X 106 psi; S 6000 psi %3D Ans. 204. A uniform bar of length L, cross-sectional area A, and weight W is sus- WL If pended vertically from one end. Show that its total elongation is & = 2AE wL? its weight per unit volume is w, show also that & 2E A steel rod having a cross-sectional area of sq in. and a length of 600 ft is suspended vertically. It supports a load of 5000 lb at the lower end. If steel 30 X 106 psi, find the total elongation in the rod. Ans. 8 = 2.64 in. 205 weighs 490 lb/cu ft and E Hint: Use the result of Prob. 204. steel wire 30 ft long, hanging vertically, supports a…
The information in the photo attached shows elastic properties of a human tibula bone. If you were to take a small cuboidal cross section of the tibula bone and apply the ultimate shear stress, what would be the resulting strain? (a) 1.0 % (b) 6.7 % (c) 10 % (d) 15 % (e) None of the above.
A machine component is subjected to a load of P = 3,800 N. Which stress element represents the state of stress at point H? 25 mm 3,800 N 18 mm 50 mm 5 mm 12 mm 5 mm
Calculate the true strain when the initial length 10.5 mm and the final length *12mm 0.143 O 0.134 O 0.413 O 0.314
what is the modulus elasticity of 20 mm rod when a 250 MPa stress is exerted the total elastic deformation measured is 0.2mm
Normal stress is calculated dividing the reaction by the cross-sectional area. Is this approach valid for any point of a structural member? Why or why not? To answer this question, consider the loading point, cross- sectional shape, etc.
Determine stress and longitudinal strain