Assume if the shear stress in steel exceeds about 4.00  108 N/m2 the steel ruptures. (a) Determine the shearing force necessary to shear a steel bolt 1.05 cm in diameter.   (b) Determine the shearing force necessary to punch a 2.40-cm-diameter hole in a steel plate 0.530 cm thick.

Q: A 4.8ft-long steel wire of 1/4in-diameter is subjected to a 750lb-Tensile load. Knowing that…

A: Concept: We will find the elongation of the wire due to applied load using the formula for…

Q: A steel rod having a cross-sectional area of 0.002 sq. m. and length of 1.5 m. is attached to…

A: Force exerted by the supports on rod is given by: F=EαTA Where, E = Modulus of elasticity T =…

Q: An aluminum bar having a cross - sectional area of 150 mm2 carries an axial load in three sections…

A: Given Data,  Length of AB= 0.8m Length of BC = 1m Length of CD=0.6m

Q: 2. A metal plate is .125 inch thick. What force is required to punch out a square piece 1" x 1"? Th…

A: Thickness of metal plate is 0.125 inch Size of square piece is 1''×1'' The ultimate shear stress of…

Q: A steel of cross-section area 100 mm² and 1 m long is subjected to a tensile force of 40 kN. What is…

A:

Q: A steej two fixed points. The tensile force in the rod at 70°F is 1200lb. If a = 6.5x10-6/°F and E =…

A:

Q: A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress…

A: This question is related to the Strength of material. In this question we calculate axial stress and…

Q: Given that a steel cyInder of dimenslons 12.0 mm in dlameter and 70 mm bng is subjected to tensicn.…

A: a) According to Hook's law within the elastic limit, stress is directly proportional to strain.…

Q: HAMMA A steel bar 100 mm long is subjected to a tensile stress o. If change in length of bar is 0.05…

A:

Q: The aluminum machine part is subjected to a moment of 75 kNxm. Determine the bending stress created…

A: Solution:Given: The moment acting on the section is M=75N.m which is sagging, so the topmost fiber…

Q: 1.17 Figure P1.17 shows the stress-strain relations of metals A and B during tension tests until…

A: Any pressure of a solid object creates a stretched internal stress, similar to the spring-turning…

Q: Consider the following figure showing state of stress at a given point in a structural or nachine…

A: Solution: Given Data: σx=150 MPaσy=-100 Mpaτxy=50 Mpa (a) normal stress in x direction…

Q: A steel wire of 20 mm diameter is bent into a circular shape of 10 m radius. If E, the modulus of…

A:

Q: Sample: Malleable Steel (AISI 4145) Original Diameter: 6.14mm Gauge Length: 55 mm Final Length:…

A: Given data, Original diameter D = 6.14 mm Gauge length L = 55 mm

Q: A bar obtained by bonding together pieces of steel (E = 29 x 106 psi) and brass (E = 15 106 psi) has…

A: Given : Es = 29 X 106 psi Eb = 15 X 106 psi M = 40 kip-in. This is a problem of Solid mechanics…

Q: A punch must cut a hole 30 mm diameter in a sheet of steel 2 mm thick. The ultimate shear stress is…

A: A punch must cut a hole 30 mm diameter in a sheet of steel 2 mm thick. The ultimate shear stress is…

Q: A tensile stress is applied along the long axis of a cylindrical steel rod with a diameter of 10 mm.…

A: It is required to calculate the strain in the x-direction. Here, is the change in diameter, and do…

Q: 1.3 (A). Define the terms shear stress and shear strain, illustrating your answer by means of a…

A: SHEAR STRESS: It is defined as the force, internal resisting force per unit area.The force acting on…

Q: A drill rod with a diameter of 12 mm is made of high- strength steel alloy with a shear modulus of…

A: Given that ; Diameter of rod = 12 mm Shear modulus = 80 GPa Allowable shear stress = 300 MPa To Find…

Q: condition of plane stress are: of the principal stresses in the

A:

Q: Assume if the shear stress in steel exceeds about 4.00 x 10^8 N/m2 the steel ruptures. (a) Determine…

A: Given : Allowable shear stress = 4 X 108 N/m2 Diameter of steel bolt = 1.05 cm Diameter of hole =…

Q: Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A:

Q: A 26-foot-long structural steel bar is being tensed along its centroidal axis. Point B is being…

A:

Q: Q. A For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A: Note:- as per our company guidelines we are supposed to answer only first part. Kindly repost other…

Q: A 2 m long, axially loaded mild steel rod of 8 mm diameter exhibits the load- 14000 12000…

A: A graph of displacement against load, yield stress, length of mild steel rod, Diameter have been…

Q: A cylindrical steel alloy rod with a 0.5 in. diameter is subjected to tension.Determine the…

A: It is required to calculate the strain in the x-direction. Here, is the change in diameter, and do…

Q: A steel section as shown in figure is subjected to a shear force of 20 kN. What will be shear stress…

A:

Q: A steel bar with a length of 3 m, diameter of 25 mm, modulus of elasticity of 207 GPa, and linear…

A: Given: The length of the steel bar is 3 m. The diameter of the steel bar is 25 mm. The modulus of…

Q: 10.1. A 0.505-in-diameter mild steel specimen was tested to failure in a tensilé tëstihg fma- chine…

A: a}

Q: A 19-mm reinforcing steel bar and a gauge length of 75 mm was subjected to tension, with the results…

A: Given: Diameter of steel bar d, is 19 mm. Gauge length l, is 75 mm. The table is given below,

Q: The state of stresses in the x and y directions at a point in a given material is shown in the…

A: step 1-

Q: The state of stresses in the xand y directions at a point in a given material is shown in the figure…

A: step 1-

Q: A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to ten- sion. Determine the…

A:

Q: A tensile stress is to be applied along the axis of a cylindrical steel rod that has a diameter of…

A: Given data : Poisson's ratio (μ)=0.3Diameter (d)=7.5 mmModulus of elasticity (E)=207 GPaChange in…

Q: The state of stresses in the x and y directions at a point in a given material is shown in the fig…

A:

Q: (a) What is the permanent set of the bar (in mm)? 2.184 ] mm (b) If the bar is reloaded, what is the…

A: Given that,  length of bar = 390 mm elongation = 2.34 mm Therefore, strain,  ε=ΔLL=2.34390=6×10-3…

Q: Figure P1.16 shows the stress–strain relations of metals A and B during tension tests until…

A: (a) The proportion limit is the point on the the graph upto which the stress strain  curve is…

Q: This figure shows typical stress-strain behaviour for a brass. The inset figure shows the behaviour…

A: Given Data: Initial length of test sample is L=14 cm. Initial radius of test sample is R=2 mm.

Q: The stress in a steel bar is given as 25,0000 kN/m² and length of the bar is 50 m. Calculate the…

A: Stress in a steel bar = 250000 kN/m2Length of bar = 50 mE = 2.14 X 108 N/mm2TO Find :Shortening of…

Planar Stresses