I. Problem Solving: Answer what is being required. Show you complete solution. 1. Compute the compressive stress for the respective ages of the specimen. The diameter of the specimens is 150mm and the height is 300mm. Load (N) 176,000 252,000 340,000 Stress (MPa) Age 7days 14 days 28 days 2. Compute the tensile stress from the value acquired from the experiment if the breaking load is 105KN. The diameter of the specimen is 150mm and the height is 300mm. 3. Compute the flexural stress of the sample specimen if its dimension is 150mm x 150mm x 500mm in a 3 point loading. The effective length is 400mm. The specimen failed at 44,300N in the middle third.

I. Problem Solving: Answer what is being required. Show you complete solution. 1. Compute the compressive stress for the respective ages of the specimen. The diameter of the specimens is 150mm and the height is 300mm. Load (N) 176,000 252,000 340,000 Stress (MPa) Age 7days 14 days 28 days 2. Compute the tensile stress from the value acquired from the experiment if the breaking load is 105KN. The diameter of the specimen is 150mm and the height is 300mm. 3. Compute the flexural stress of the sample specimen if its dimension is 150mm x 150mm x 500mm in a 3 point loading. The effective length is 400mm. The specimen failed at 44,300N in the middle third.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solid shaft made of cast iron shown in the figure, T = 400 lb. It is subject to flick torque. Determine the smallest radius that will not generate strength loss according to the theory of greatest normal stress? The cast iron sample tested in tensile has a stress of 20 µm axim um.
A tensile bar has an initial 2.000-in. gauge length and a circular cross-sectional area of 0.2 in.?. The loads and corresponding gauge lengths recorded in a tensile test are show below. After fracture the bar diameter was 0.370 in. Load Gauge length (in.) (Ib) 2.0000 6,000 12,000 15,000 18,000 21,000 24,000 25,000 22,000 2.0017 2.0034 2.0042 2.0088 2.043 2.30 2.55 B.00
At a temperature of 33.37 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 115.33°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L= 325.86 mm and M = 234 mm. Round off the final answer to four decimal places. d ... A В Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6/°C A = 800 mm² E = 190 GPa a = 17.3 × 10-6/°C
Please solve all part ? and correct
Solve the problem and give what is asked in this problem. box the final answer clearly and readable.
During tensile testing, you forgot to measure the change in the longitudinal dimension of the sample. However, you have managed to measure change in the cross-sectional area with time. With this information alone, will you be able to estimate the true strain exhibited by the material at a given time t. How accurate would such estimation be?
ANSWER A PLS
O (MPa) 80 60 40 20 0.002 0.004 0.006 0.008 0.01 0.012 Figure 3 i) Determine the value of yield strength. ii) Determine the value of ultimate strength. iii) Determine the value of modulus of elasticity iv) If the specimen is loaded to a stress of 65 MPa and then unloaded, determine the residual plastic strain. v) If the diameter of the unloaded specimen is 1 cm and the Poisson's ratio pf the material is v = 0.3, what is the specimen diameter just prior of yield of the tensile specimen? CS Scanned with CamScanner
Following experimental data are obtained from tensile test of a rectangular test specimen with original thickness of 2,5 mm, gauge width of 24 mm and gauge length of 101 mm: Load (N) Elongation (mm) 0 0 24372 0,183 23008 0,315 28357 5,777 35517 12,315 27555 17,978 23750 23,865 Based on the information above; draw stress-strain diagram of the material and answer the following questions. 1-)-Determine the modulus of resilience (in N.mm/mm3) of the material. (Use at least five decimal units) 2-)- Determine the elastic energy absorption capacity (in N.mm) of that specimen. 3-)Determine the plastic energy absorption capacity (in N.mm) of that specimen.
The (G-E) diagram obtained in the tensile test performed on a metal sample with a diameter of 16 mm is as follows. The loads at points A, B and C and the elongation measured on l. 16 cm gauge length were determined as follows: B A B C Load (kgf) 4800 8400 7200 Elongation (mm) 0.192 28.8 38.4 c) Calculate the fracture work and the maximum elastic energy the metal rod can store. d) Find the cross-sectional area of a 6 m long rod made of this metal such that it can carry 12 tons of load with 2 times the safety of yield strength. How long does the rod extend under this load?
A steel alloy specimen having a rectangular cross section of dimensions 19.1 mm x 3.1 mm (0.7520 in. × 0.1220 in.) has the stress-strain behavior shown in the Animated Figure 6.22b. If this specimen is subjected to a tensile force of 98290 N (22100 Ib;) then (a) Determine the amount of elastic strain induced. (b) Determine the amount of plastic strain induced. (c) If its original length is 610 mm, what will be its final length after this force is applied and then released? The elastic modulus for steel is 207 GPa. (a) i (b) i (c) i mm
(c) A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a compressive stress of 50 N/mm² in a direction at right angles to the previous one. Find fully the stresses on a plane the normal of which makes an angle of 40 degree with the 70 N/mm² stress.