At a temperature of 33.37 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 115.33°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L= 325.86 mm and M = 234 mm. Round off the final answer to four decimal places. d ... A В Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6/°C A = 800 mm² E = 190 GPa a = 17.3 × 10-6/°C

At a temperature of 33.37 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 115.33°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L= 325.86 mm and M = 234 mm. Round off the final answer to four decimal places. d ... A В Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6/°C A = 800 mm² E = 190 GPa a = 17.3 × 10-6/°C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum [E = 11500 ksi] control rod with a circular cross section must not stretch more than 0.21 in. when the tension in the rod is 2080 lb. If the maximum allowable normal stress in the rod is 11.5 ksi, determine: (a) the smallest diameter d that can be used for the rod. (b) the corresponding maximum length L of the rod. Answers: (a) d = i (b) L = i in. in.
The assembly shown in figure below consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is touch to its support. A 0.75 m Steel A = 250 mm E = 200 GPa *i* O 1.5 m Aluminum L = 2m A = 300 mm' E = 70 GPa B D
Problem # 2. At room temperature (20°C) a 0.5-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 140 °C, determine (a) the normal stress in the aluminum rod Ans: A -300 mm Aluminum A = 2000 mm² E = 75 GPa α = 23 x 16-6/°C 0.5 mm -250 mm Stainless steel A = 800 mm² B E = 190 GPa a = 17.3 x 10-6/°C
At a point on the surface of a machine component the stresses acting on the e face of a stress element are or = 55 MPa and Txy = 30 MPa (see figure). T- 30 MPa a, = 55 MPa What is the allowable range of values for the stress oy if the maximum shear stress is limited to TO = 34 MPa? Round to one decimal place. (a) Lower limit is MPa (b) Upper limit is MPa
An aluminum shaft has a diameter of 50.1 mm. Determine the maximum shear stress in the shaft when subjected to a torque of 26.5 Nm? (answer in MPa or MN/m² to 1 decimal place, use pi = 3.142)
A steel wire (E = 200 GPa) of diameter d = 1.0 mm is bent around a pulley of radius Ro= 400 mm (see figure below). Ro a. What is the maximum stress in the wire? b. Does the stress increase or decrease if the radius of the pulley is increased?
At a temperature of 27.89 °C a 0.41-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 126.64°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 320.36 mm and M = 231 mm. Round off the final answer to four decimal places. d ... M A B Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6/C A = 800 mm² E = 190 GPa %3D a = 17.3 × 10-6/°C
For P = 100 MPa, determine the range of values of τxy for which the maximum tensile stress is equal to or less than 60 MPa. (Round the final answer to one decimal place.)
At a temperature of 28.42 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 137.38°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 339.61 mm and M=240 mm. Round off the final answer to four decimal places. d ... В Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6°C A = 800 mm² E = 190 GPa a = 17.3 × 10-6°C
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
At room temperature (20°C) a 0.7-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 150°C, determine: (a.)The normal stress in the aluminum rod, (b.) The change in length of the aluminum rod. 0.7 mm 300 mm A Aluminum A =2,000 mm² E= 75 GPa α = 23 x 106/°C 250 mm B Stainless steel A = 800 mm² E = 190 GPa a = 17.3 x 10-6/°C
Knowing that a 0.02in gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11ksi, (b) the corresponding exact length (2 decimal places in 103 inches) of the aluminum bar. 0.02 in. 14 in. Bronze A = 2.4 in² E = 15 × 106 psi a = 12 x 10-6/°F 18 in. Aluminum A = 2.8 in² E = 10.6 × 106 psi a = 12.9 x 10-6/°F