Problem 2: Let FA=100 N and Fc= 208.33 N for the shaft below. The bearings D and B act as pin supports. The shaft is made of 2014 aluminum alloy with a yield strength of 276 MPa. The shaft has a diameter of 8 mm. Based on the maximum shear stress (MSS) theory, determine if the shaft is safe. Determine the corresponding safety factor.

Problem 2: Let FA=100 N and Fc= 208.33 N for the shaft below. The bearings D and B act as pin supports. The shaft is made of 2014 aluminum alloy with a yield strength of 276 MPa. The shaft has a diameter of 8 mm. Based on the maximum shear stress (MSS) theory, determine if the shaft is safe. Determine the corresponding safety factor.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Squared and grounded spring
Please answer it ASAP, Thank you!
A shaft made of steel has the following minimum properties Se = 264 MPa, Sy = 413 MPa, and Sut = 536 MPa. The shaft is transmitting fixed torsional stress of 155 MPa and is subject to an alternating bending stress of 74 MPa. Find the factor of safety guarding against fatigue failure using Modified Goodman criterion. accepted answer range (+/- 0.2).
PROBLEM 12 A 20 mm shaft is loaded as shown below (Sy = 290 MPa). Determine the location of maximum stress and calculate the von Mises stress and factor of safety. L = 0.4 m, L₁= 0.25 m, F = 400 N, d, 100 mm, b = 20° Bearings are treated as simple supports. The tangential component of the force will produce a torque on the shaft in addition to the bending moments. 2006
Find the shaft diameter and the factor of safety against yielding
An aluminum alloy is to be used for a solid drive shaft such that it transmits 30 hp at 1200 rev>min. Using a factor of safety of 2.5 with respect to yielding, determine the smallest-diameter shaft that can be selected based on the maximum shear stress theory. sY = 10 ksi.
4. A beam has fluctuating bending moment and is not rotating. The bending moment has a maximum of 1kNm and a minimum of 100kNm. The beam is made of AISI1020CD steel with a square cross section. There are no stress concentrations. a. Determine the fully corrected endurance limit as a function of the cross section (cross section unknown) b. Determine the required size for a factor of safety of 2 using the Gerber Fatigue Failure Theory
42. The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find the value of the critical speed. Shaft is steel. Ans. n = 1810 rpm. Design of Shafts Chap. 3 248 t. 50 30 1"dia 10" 10" Figure 3-52 Problem 41. 10 kg 10 kg C B 375 600 mm 375 Figure 3-53 Problem 42.
Dr. (ny) A = 5.52 تمارين : واجب بيتي 1. The solid steel shaft 100 mm in diameter and 8 m long was made of AISI 1020 HR steel is subjected simultaneously axial to an compressive force of 200 kN and a torque T. find the maximum applied torque T depending on the maximum shear stress, if the factor of safety is 1.5 and Ssy === Sy (Neglect buckling) 600 kN 30 T 100 mm 600 kN Prepared by Dr. Hazim Khale anc dir the dia BC (b to ca th th n
A leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches apart and the system should carry a load of 400 lbs. If the thickness of the available bronze plate is 1“ and Sy = 80 ksi, what leaf width is required at FOS = 8?
30 min. Q4 (DÖÇ-1) For the given gear-shaft system failure shear stress for the shafts is 90 MPa, If the factor of safety is 1.5 and the diameter of the shaft CD is d2 = 60 mm, determine the minimum diameter of shaft AB, d,. Shafts turn freely within the bearings. rg = 150 mm, rc = 100 mm B
The figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The forces shown acting on the pulley surfaces represent the belt tensions. The shaft is to be made of ASTM grade 25 cast iron using a design factor na = 2.8. What diameter should be used for the shaft? 6-in D. 300 lbf 27 lbf 360 lbf D 6 in A 8 in 50 lbf B 8-in D. 8 in