Problem 1. Beam ABC has the given loading, Length, L, and a rectangular cross section with width b and height h. The concentrated couple M is related to the concentrated force P by M = PL. Find the maximum absolute value, |Pmarl; of force P if a) The allowable bending stress is oal, b) The allowable shear stress is Tall P -L/2- -L/2- h M A B b

Problem 1. Beam ABC has the given loading, Length, L, and a rectangular cross section with width b and height h. The concentrated couple M is related to the concentrated force P by M = PL. Find the maximum absolute value, |Pmarl; of force P if a) The allowable bending stress is oal, b) The allowable shear stress is Tall P -L/2- -L/2- h M A B b

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Required information Consider the beam and loading shown. If a=8 in, b=9.0 in, c=1 in. For a section at n-n, determine the shear stress at b. A 25 kips 20 in.- 10 in. 25 kips - 20 in.- B a +6 i in.. in. b b a с in.
3. Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional area of each bar so the bars fail at the same time with the load is P = 4 kips. Use a factor of safety of 1.8. 3 ft 4 ft P B σ (ksi) 25 20- 15 10- 5H 0 0 tension. compression 0.20 0.40 0.60 0.80 e (in./in.)
Problem 7. [Concepts: Allowable stresses and factor of safety] Two aluminum rods AB and AC support a vertical load P. The allowable tensile stress for the aluminum is Gallow = 150 MPa. a) If P = 20 kN, determine the required diameters of the rods AB and AC. b) If the diameters of the rods AB and AC are 10 mm and 8 mm, respectively, determine the largest vertical force P that can be supported. U B
The cross section of a wood beam carries a bending moment M of magnitude 20R lb.-in. acting at 100 to the horizontal. Determine(a)the angle between the neutral axis and the horizontal; and (b) the maximum bending stress acting on the cross section. Note: ( R=990)
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
A simply supported wood beam that is 13.2 m long carries a 41 kN concentrated load at B. The cross-sectional dimensions of the bearn are b = 125 mm, d = 350 mm, a = 110 mm, and c= 35 mm. Section a-a is located at x= 2.2 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entirespan. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P. a H a a B C K 2L 3 3 Answer: (a) TH = i 689 КРа (b) TK = i КРа 280 (c) Tmax= i 799 kPa (d) Omax= 47.11 MPa
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
TEXT:A planar construction is composed of two beam elements and two axial rods. These arejoined with frictionless joints, as indicated on the sketch. The structure is applied an outer concentrated load P=8kN in node G and a downwardevenly distributed load q=4kN/m between junctions A and D. The beam ABCD and EFG are torque rigid,while the axial rods BF and CF only absorb forces in the direction of the rods. A) Calculate the rod forces and for the external given load effect.B) Calculate the bearing reactions for the external given load effect.
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
A bridge girder AB on a simple span oflength L =14 m supports a distributed load of maximumintensity q at mid-span and minimum intensityq/2 at supports A and B that includes the weight ofthe girder (see figure). The girder is constructed ofthree plates welded to form the cross section shown.Determine the maximum permissible load q basedupon (a) an allowable bending stress σallow =110 MPaand (b) an allowable shear stress τallow = 50 MPa.
Beam AB is supported as shown in the figure. Tie rod (1) is attached at B and C with double shear pin connections, while the pin at A is attached with a single shear connection. The pins at A, B, and C each have an ultimate shear strength of 57 ksi, and tie rod (1) has a yield strength of 33 ksi. A concentrated load of P = 14 kips is applied to the beam as shown. A factor of safety of 2.4 is required for all components. Determine: (a) the minimum required diameter for tie rod (1). (b) the minimum required diameter for the double shear pins at B and C. (c) the minimum required diameter for the single shear pin at A. 6.7 8 in. 3.8ft (2) 8.5ft
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 520 mm?. If the stress in the bar must not exceed 650 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 8 m, b = 4.8 m, and c= 10.4 m. (1) B' a Answer: P = i kN