L 164 T

Q: determine the required diameter of the steel and aluminum rods.

A: Torque: - It is type of force which produces rotational motion in a body. Also called as rotational…

Q: The section of a thick beam has the dimensions Calculate the section properties I,, I, and I,…

A: The direct stress is generally produced by bending moments or by the bending action of shear loads…

Q: (1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural…

A: It is asked to check the nature of flexural stress at point A & B in the beam. For this it is…

Q: 3. Determine the principal stress, the maximum in-plane shear stress, and average normal stress.…

A:

Q: (2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio…

A: when a point load acts on cantilever top portion is under tensile stress and bottom is compressive

Q: Determine the maximum force P that can be applied to the specimen. The bar is made from steel and…

A: w=150 mmh=50 mmr=20 mmt=6 mmwh=15050=3rh=2050=0.4From graph, K=1.51σavg=σallK        =1501.51…

Q: A flat bar of a width b = 60 mm and thicknesst = 10 mm is loaded in tension by a force P…

A: (a) Determine the pin diameter dmforwhich the load P is a maximum.(b)Determine the value of maximum…

Q: Determine principal stress and maximum shear stress 200 MPa

A: Given data : Normal stress in X direction (σX)=350 MPaNormal stress in Y direction (σY)=-200…

Q: When the normal stresses are at their maximum or minimum values, the shear stresses are zero. We can…

A: 1 true 2 true 3 false 4 true 5 true

Q: An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the…

A:

Q: Three round bars welded together axially loaded as shown. Find the normal are stress in each bar if…

A: Stress is defined as the force acting per unit area of a bar. The stress in a bar is directly…

Q: Q- A stepped steel shaft is subjected to a clockwise torque of 10 Nm at its free end. Shear modulus…

A: Given- Clockwise torque T=10 NmG=80 GPa=80×103 N/mm2Strain energy in the shaft needs to be find out.

Q: Find the value of maximum principal stress if maximum shear stress is 60 MPa and minimum principal…

A: Given data : The value of minimum principal stress σ2=50 MPa The value of maximum shear stress…

Q: Q- The normal stresses on the two mutually perpendicular planes at a point are 120 MPa (Tensile) and…

A:

Q: b 7'

A:

Q: Determine maximum shear stress and maximum principal stress

A: Given data : The value of normal stress in X direction σX=80 MPa The value of normal stress in Y…

Q: A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its…

A: A steel pipe is subjected to the 16-kN load shown below.Outer diameter = 140 mmThickness = 7 mmYield…

Q: A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength…

A: Given:- uniform load=q=200 lb/ft a=12ft b=6ft L=18ft To find:- (a) the maximum tensile stress σt and…

Q: Using the CREMONA method, determine the forces and types of stress in the bars and analyze them.

A: To analyze the truss using the **Cremona method**, follow these steps:### Step 1: Identify all the…

Q: 'bo Part A If it is made from a plate that has a constant width bo, determine the absolute maximum…

A: Calculate the maximum bending moment in the beam.

Q: 2. (3 points) When loading is applied at a point on a body, the stress distributions at different…

A: Saint Venant’s principle

Q: D 900 mm E a 300 mm 20 mm 50 mm 25 mm")25 mm 25 mm Section a - a

A: Given data  Dimensions  Radius  Maximum allowable stress

Q: mine the value of 0 if the shearing stress on the glued joint is thrice that of the normal

A:

Q: Determine the length of the cantilevered beam so that the maximum bending stress in the beam is…

A: Determine length of cantilever beam,L=?

Q: A stress developed if the applied force is parallel to the resisting area refers to: O tangential O…

A: A stress developed if the applied force is parallel to the resisting area refers to tangential.…

Q: A steel rectangular block is subjected to a uniform stress of o = 150 MPa acting on all faces. The…

A:

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.