Answered: L - 25 in. - 25 kips For the beam and…

L - 25 in. - 25 kips For the beam and loading shown, determine:. 5. The shearing stress at point a ( ksi) T 3 in. 6 in. b - 8 in. t = 0.25 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported wood beam that is 13.2 m long carries a 41 kN concentrated load at B. The cross-sectional dimensions of the bearn are b = 125 mm, d = 350 mm, a = 110 mm, and c= 35 mm. Section a-a is located at x= 2.2 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entirespan. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P. a H a a B C K 2L 3 3 Answer: (a) TH = i 689 КРа (b) TK = i КРа 280 (c) Tmax= i 799 kPa (d) Omax= 47.11 MPa
A simply supported wood beam that is 9.3 m long carries a 31 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 400 mm, a = 80 mm, and c = 30 mm. Section a-a is located at x = 1.6 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. a Н to A a В K 2L 3 3 Answer: kPa (a) TH = i kPa (b) TK = i kPa (c) Tmax = i MPa (d) Omax = i
For the beam and loading shown, consider the n-n section. (a) Absolute value of shear force in n-n section |V| In kN units, (b) the absolute value of the shear stress at point a of the n-n section |τ| Specify in MPa units. Take the P value of 34 kN and the D value of 17 mm in the question.
la. Draw the V and M Diagram 10kN/m 12KN/m 5kN/m 3kN-m 3m 2m 2m 3m 1b. Compute for the maximum bending stress of the given beam if the cross sectional area is: 30mm 30mm 60mm 1.c. Compute the flexural stress at 3m from the hinge if the cross sectional area is: Equilateral Triangle 100mm
A simply supported wood beam that is 14.1 m long carries a 47 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 360 mm, a = 70 mm, andc = 20 mm. Section a-a is located at x = 2.4 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. y H a a A В K L 2L Answer: (a) TH = i kPa (b) TK = i КРа (c) Tmax = i kPa (d) Omax MPa i 13
QUESTION 1) The cross sectional Е, A, Е, А, areas of the KM and MR intervals are A1 = 400 mm? and A2 respectively. Both sections are made = 200 mm², from the same material that has elastic L. M N R K modulus ofE = 200 GPa. If the gap in figure is 8-5mm and the axial forces are Pi = 120 kN and P2 1m 2m 2m 1m = 80 kN; a) Calculate the support reactions. b) Draw the axial force diagram.
Problem 2 The lap joint is fastened with four 3/4" diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. ANS: P = 47.3 kips P P 7 in. 8 4 in. 7 81 in. P
a) 25.0 lb/in2 b) 56.25 lb/in2 c) 18.75 lb/in2 d) 31.25 lb/in2
A T-shape beam is subjected to a vertical shear force of V = 30 kN. The beams centroid is located 211.1 mm above the bottom surface of the beam, and the moment of inertia is l₂ = 48.7 x 106mm4.[b = 178 mm, h = 300 mm, t₁ = 12.7, tw = 9] b h tw Determine the shear stress in the flange at the intersection of the flange and the web. 6.96 MPa 7.6 MPa 2.94 MPa 4.3 MPa 6.09 MPa
A simply supported wood beam that is 9.3 m long carries a 31 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 400 mm, a = 80 mm, and c = 30 mm. Section a-a is located at x = 1.6 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P y H a A a B C 2L 3 Answer: (a) TH = i kPa kPa (b) TK = i kPa (c) Tmax = i MPa (d) Omax= i
The uniform beam is supported by two rods AB and CDthat have cross-sectional areas of 10-mm2 and 15-mm2,respectively. Determine the stress on two rods AB and CDif the uniform load is 5N/m.
1. Calculate the moment of inertia of the section in mm . 2. Calculate the location of the neutral axis from the bottom of the beam in mm. 3. Calculate the maximum moment in the beam in kN.m. 4. Calculate the flexural stress at a section 75mm from A and 40mm from the bottom of the beam in MPa. 5. Calculate the maximum compressive flexural stress of the beam in MPa. 6. Calculate the maximum tensile flexural stress of the beam in MPa. NOTE: Kindly answer all numbers with complete solution please. Needed ASAP.