2) The strain in the x direction at point A on the A-36 structural-steel beam (E = 29,000 ksi, v = 0.318) ismeasured and found to be & = 200 x 10". Determine:a) The applied load P in kips.b) The shear strain (y)xy at point A [Ans. to check: yy=-27.5 (10%) radians]-3 ft-12 in.4 ftP2 in.TAI 112 in.4T6 in.

Given data : E = 29000 ksi and v = 0.318 Determine : 1 ) The applied load P ? 2 ) The shear strain…

2) The strain in the x direction at point A on the A-36 structural-steel beam (E = 29,000 ksi, v=0.318) is measured and found to be & = 200 x 106. Determine: a) The applied load P in kips. b) The shear strain (Y)xy at point A [Ans. to check: y=-27.5 (106) radians]

2) The strain in the x direction at point A on the A-36 structural-steel beam (E = 29,000 ksi, v=0.318) is measured and found to be & = 200 x 106. Determine: a) The applied load P in kips. b) The shear strain (Y)xy at point A [Ans. to check: y=-27.5 (106) radians]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The question is
For the 2-D truss with the applied Loads shown below, the strain energy in the member XY is m. For member XY is assume AE= 30KN, where A is cross-section area and E is the modulus of elasticity.
how to solve this one fast please
R14-9. The 60 strain ronette is mounted on a beam. The following readings are obtained for each gage:, = 600(10, 4= -700(10, and = 350(10). Determine (a) the in-plane principal strains and (b) the maximum in-plane shear strain and average normal strain. In cach case show the deformed element due to these strains. Gor
Please solve d and e.
P A B 1m E 1m 2m The simply supported beam shown has a solid rectangular cross section having beam width of 130mm and a height of 200mm. Assuming values of P = 25KN, w = 30 kN/m, and E = 5m, determine: 1) The max tensile bending stress in MPa (enter this value into D2L answer box, in MPa). Exactly where does this occur along the beam? (4 sigs) 2) The max shear stress in MPa. Exactly where does this occur along the beam? ( 4 sigs) Your Answer:
The rigid beam is supported by the three suspended bars. Bars AD andCF is made of A-36 steel and BE is made of 2014-T6 aluminum alloyeach having a cross-sectional area of 450mm2. Determine the angle oftilt of the rigid beam DEF and the average normal stress in each bar ifthe rigid beam is subjected to the loadings shown. Take ESt = 200 GPa and EAl = 73.1 GPa.
* For the beam and loading shown with P = 2 kN, consider section n-n and determine (a) the largest shearing stress in that section, (b) the shearing stress at point A. Problem #1 1m C n 2 m B -1 m- -150 mm- 125 mm 200 mm 25 mm 25 mm Pt. A is just below 25 mm
If the applied load "P" causes the point C to be displaced downward by &c=1 mm, determine the normal strain in members AC and BC. The unloaded lengths are LAC-210 mm and LBC=480 mm. A The strain for link AC is The strain for link BC is 60° 45° Submit Question O Is Question Help: Message instructor SC B
Determine the stress in each member of the truss shown. Get first the value of RAv then Find the value of member AE @ Joint A
Two steel plates are welded together to form an inverted T-beam and are loaded as shown below. Determine the maximum bending stress developed. Also, determine the maximum shear stress at the neutral axis of the cross section. The following Inte Av = 9K Bv = 11K location of centroid = 3.56" above X-Ref Shear diagram Moment diagram 1" x 10" steel plate 1" x 8" steel plate X-reference A 6' 8K 12' 24' 12K 6' B of your work is accurate. Yo ment Mmax = 66K' Vmax 11K Moment of Inertia = 218 inª
2. Member AB shown in the figure supports a 5 N/mm uniformly distributed load and 4kN concentrated load as shown in the figure. Determine the position x of these loads so that the average tensile stress in the tie rod AC is equal to 90% of the compressive stress at the smooth support B. The rod has a diameter of 19 mm and the contact area at is 700mm². (Hint: quadratic formula) B A X 5 N/mm 4 kN 300mm B